-
DDanny Prosser replied to the thread Ferguson 135 diesel wont run.Not sure if it's the same or not but i've got a 230 diesel and where the diesel fuel line goes into the end of the injector pump it's...
-
DDanny Prosser replied to the thread The old glass water jug..We had gallon pickled pig feet jars with the big top to put ice in and take to the fields or fishing or whatever.
-
DDanny Prosser replied to the thread Thank you.Welcome and enjoy! I'm retiring in September and I've got 2 tractors I use a 640 and a 3000 ford diesel that I'm going to work on and...
-
DDanny Prosser replied to the thread Shop Wiring.Thanks so much Mr. John T. p your self.
-
DDanny Prosser replied to the thread Shop Wiring.No I didn't. And like I said it states you can't use romex in conduit for underground or damp conditions. It has to be single straqnd in...
-
DDanny Prosser replied to the thread Shop Wiring.#1 Not going to be sell the property it's going to be left to my grand kids. #2 I already have a lot of 10 and 12 wire so I'm not going...
-
DDanny Prosser replied to the thread Shop Wiring.Thanks but I already have that wire and I'm using 20 amp breakers.
-
DOk friends I'm ready to start trying to wire the inside of my shop. I'm going to use 10/2 for recepticales and 12/2 for the lights. My...
-
DDanny Prosser replied to the thread Ford Jubilee loader?.I've got one I took off on a Jubilee that I had put a new hydro pump control valve and crank to pump coupling on. I'd let it go for what...
-
DDanny Prosser replied to the thread Black ink only printer.I just bought one from Best Buy it's a HP and it can work wired or wireless and used a toner cartridge instead of ink. That's much...
-
DDanny Prosser replied to the thread Light Fixture question.Thanks everybody!
-
DGood day my friends. My tractor/work shop is 24' deep and 36' wide. I've got a bunch of 4' 4 tube fluorescent fixtures and bulbs. The...
-
DDanny Prosser replied to the thread Retirement.I had my 30 at 50 and could have retired then but decided to stay.
-
DDanny Prosser replied to the thread New (to me) toy. 1957 Ford 601 Workmaster.I have a 640 mutt it's got a Jubilee engine in it. Their pretty much bullet proof as long as something doesn't come lose and come out...
-
DDanny Prosser replied to the thread Retirement.Yes I would say it is I feel a little scared myself. I can hunt and fish and grow my own garden if I have to in order to eat. About the...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy