-
Steve in IL replied to the thread Ford Dozer blade.Some of the main frame might be there, hidden. Because that is what the lower portion of the lift cylinder mounts to, and you can see... -
Steve in IL replied to the thread Turf tires for ford 3000.Dave - I think you are likely looking for essentially the same tire size, but a different tread pattern. The Maxam Tire website has a...
-
-
Steve in IL replied to the thread Ford Dozer blade.It’s tough to see, but the main frame is the portion that extends forward to the bottom of the cylinder, and goes back to the bottom...
-
-
Steve in IL replied to the thread Ford Dozer blade.Agree Agree with Ernie. Decent snow blade. Will need to lock spring trip release if you push anything more significant.
-
-
Steve in IL replied to the thread 1971 Ford 4000 3cyl gas has starting and stopping issue(fickle).Had same issue with our 4000 SU…. Turned out to be loose ground at frame end. Perhaps check/clean/tighten all four main battery cable ends?
-
Your loader isn't non-removable, just a major PITA to remove!
-
Steve in IL replied to the thread Ford 660 barely runs..Ok… Maybe give the sprayed gas technique a try. I find it’s a great method to determine if you have a fuel supply issue. Most vehicles...
-
Steve in IL replied to the thread Ford 660 barely runs..If you spray some gas (use an old spray bottle) directly into the carburetor (with air filter tube removed), and quickly try to start...
-
Steve in IL replied to the thread May 4 tractor.Has anyone seen anything like this before? A chopper mounted to the front corner of a 4wd tractor? Or is there a self propelled...
-
Steve in IL replied to the thread P68 komatsu dozer.Oh man, I am far from a Komatsu, of that era, expert (joined Cat in 88). I will say that generally Komatsu dozers are well built (good...
-
Steve in IL replied to the thread P68 komatsu dozer.Perhaps you mean Komatsu D68P-1 or D68E-1? Both of these models were made from about 1988 - 1992.
-
Steve in IL reacted to FRanch's post in the thread Gravity feed diesel tank recommendations with
Like.
This is where I am at. My grandpa is now 86 years old, and lugging around 5 gallon diesel cans is just not doable anymore. The time it... -
Steve in IL replied to the thread Gravity feed diesel tank recommendations.And one more comment on installation. I had two opposing thoughts on how best to position the tank relative to 100% level. One could...
-
Steve in IL replied to the thread Gravity feed diesel tank recommendations.Yes… For the amount of gas we use (mostly my 90 year old mother), this works great. I just don’t need her toting 5 gallon cans. It...
-
Steve in IL replied to the thread Gravity feed diesel tank recommendations.Agree with Jon. I got this one for just about the value of the fuel that was in it. In addition to a quick inspection of the tank...
-
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2024 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy