(800) 853-2651
SHOP NOW

Search results

  1. G

    8030 Power Shift

    Or do you know of someone I could call to talk to? It has been 30 years since working on one
  2. G

    8030 Power Shift

    Am looking at an 8030 power shift. The complaint was that it was slipping in reverse. Tested supply pressure to valve body. It is over 250 at pump supply pressure. Modulator pressure is 130, book shows it should be 210-230. I removed cap from lube pressure relief valve on top front of valve...
  3. G

    CA Hydraulics

    A friend just called me and said he rebuilt the hydraulic pump on a CA he is working on and now the lift arms go right up, but wont come back down. It has been too long since I have worked on this system. Looking for advice. TIA
  4. G

    Sunday Toy Collection

    I attended a similar auction yesterday. Tables full of M&M figurines, dolls, toys, clothes, etc.
  5. G

    d-17 Hydraulic pump Dr, Allis ,Please?

    Your Series 4 will be a complete different system. It will be a low pressure and higher flow system . The main relief PSI should be about 2000 PSI. Your problem will be the traction booster control spool stuck in the raise position. On the valve stack below your right hand control levers, the...
  6. G

    Allis Chalmers 8010 electronic fuel pump

    I f you are getting a flow of fuel from the tank, yes, the electric fuel pump can cause the problem. A telltale sign it is failing is that it doesnt have a smooth steady whirring sound. If you replace it, also be sure to replace it with one supplying proper pressure also, if memory serves me...
  7. G

    Ih 460 valve body leak

    Ditto on what Deltared said. On my 460 it was leaking on an o-ring where a shaft come out for the draft control linkage. It has been a few years ago, but as I recall it was kind of tricky as there were gears on the shaft internally that had to be properly timed. Get a manual to do the repair...
  8. G

    Ih 460 valve body leak

    Ditto on what Deltared said. On my 460 it was leaking on an o-ring where a shaft come out for the draft control linkage. It has been a few years ago, but as I recall it was kind of tricky as there were gears on the shaft internally that had to be properly timed. Get a manual to do the repair...
  9. G

    Replacing cam on 301 Diesel

    I always used clothes pins to hold the dowels up also, it worked for me. Sounds to me as if someone did a shoddy job previously. I wonder what other corners were cut
  10. G

    7040

    With the engine running and standing behind the tractor while it is in park standing clear of the implement, manually move the bracket connected to the remote valve and see if it operates then. Also, make sure the cable housing is properly engaged in the anchor at each end. Is the PTO and 3...
  11. G

    constant revving engine

    I would be concerned about the equipment, but more than that is the lack of respect for my desires, and disrespect which will carry over into other aspects of life as he grows older.
  12. G

    7030 primer plunger

    No, the bail - clip with the thumb screw that holds the plunger in the home position is removed to release the plunger without removing the housing. Spread the bail - wire clip apart just enough to release it from the plunger housing. When reinstalling the new primer plunger, install the...
  13. G

    8050 transfilter change

    I assume you are talking about the 2 hydraulic-differential filters underneath the rear of the tractor.. They set inside an internal canister with a spring loaded cover on the back side that seals off when removing the filters. You should only loose a half gallon or so when replacing them...
  14. G

    allis 7000 sticking gears

    Is it a maroon belly or a black belly tractor? A maroon belly has the gearshift on the floor. If it is a black belly with the shifter on the RH console check the adjustment and cable closely. Also, maroon versus black belly, dry clutch versus wet clutch, different set up and possible issues
  15. G

    Allis 200 3 pt lift/lower

    The problem is probably the traction booster - draft control valve being stuck. In the valve body, it is the outer valve, the one that doesnt have a linkage physically connected to it. The external control arm just pushes against it. The spool is probably stuck, usually not too bad. You can...
  16. G

    Rust In Gas Tank

    I have a friend who has a John Deere that has a lot of rust in the gas tank. What is a good way to get the rust knocked loose, including behind the baffle. And what do you recommend to line the inside of the gas tank with?
  17. G

    Rust In Gas Tank

    It is a John Deere 60
  18. G

    Allis 200 oil pressure switch location

    The plugs along the oil gallery are all a common eighth inch pipe thread
  19. G

    Firing order of letter series

    John Deere only had 2 cylinders, thus no need to include 3 and 4 in the equation.
  20. G

    Thank you Kc.MN!

    I enjoy your daily posts and prayers to you from the Show-Me state, Missouri
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top