(800) 853-2651
SHOP NOW

Search results

  1. A

    Tractor Seat Recommendation

    Looking for a good tractor seat. The ones we have bought for our MF35, MF250, MF265, JD1530 all do the same thing. The bottom of the seat begins to tilt forward to where you are sliding into the steering wheel. Just about impossible to drive if you have a belly. These tractors get used right...
  2. A

    MF265 Auxiliary Pump Replacement Part

    I will be replacing the Auxiliary Pump 1663627M92 on an MF265 and see where all the replacements come with a Restrictor or Pressure Relief Valve. I hope I am using the correct term. Mine does not, but I am guessing this will work. Are there any adjustments that need to be taken into...
  3. A

    MF 265 Replacing Tube from Auxiliary Pump to PTO Cover

    MF 265 TRACTOR (0001-9A349239) W/O Multi-power or IPTO AGCO Parts page 229 I am needing to replace tube 1661040M93 from the Auxiliary Pump to the PTO Cover. This one came loose from the cover and rubbed the threads raw on the adapter which allows fluid to leak. This part has been replaced...
  4. A

    Massey Ferguson 265 Split

    I will be splitting the 265 between the transmission and the center housing to inspect/replace the auxiliary pump and repair a pipe connection coming out of the left side PTO inspection cover. This 265 does not have IPTO or Multi-Power. Will there still be a pipe connection between the...
  5. A

    John Deere 1530 Battery Option

    We have a 1530 that's uses the 2-battery option. Looking at the JD parts diagram I see an option for single battery. Would the battery be just the one that is listed at CCA 550? Is that enough? Just wondering if there is anyone that uses this option and which battery they are using.
  6. A

    MF35 Clutch Finger failure

    I recently split the tractor to make some clutch adjustments and to replace input and PTO shaft seals when I noticed on of the clutch finger pins backed out about an inch. The cotter pin was sheared off with the remains still in the clutch pin. I was able to tap the clutch pin back in and...
  7. A

    MF35 Diesel Oil Pan Support

    On a Massey Ferguson 35 Diesel is the oil pan strong enough to support the front half of the tractor? There is not much surface on it until you get to the access plate which is where I was thinking about propping it up with a wooden block. I looks like it's the 732832M1 (E, M) Pan, Oil...
  8. A

    MF35 Input Shaft Seals

    Have a MF35, 6 Speed, dual clutch, non-multipowered tractor looking to replace the input shaft seals. Can this be done without access to the gearbox? I am planning to split the tractor for some clutch work and wanted to replace them while I was in there. Seen Bundy's video's and read some...
  9. A

    JD 348 Baler Auger Frame Removal

    Trying to remove the auger to do some housing work. I have removed everything I am supposed to remove per the service manual so the frame should slide out, except it is not. For one it is heavy but we can't seem to get it to budge. The rods slide freely in the frame and Auger. Only thing I...
  10. A

    MF 35 Diesel Deluxe Clutch Springs question

    About 6 years ago I replaced the clutch during a rebuild. After getting everything back together I discovered the clutch was sorta hard press. I was new to the whole thing, but I believe I replaced it with a 12 spring clutch. Its ok, but when your on the clutch with stop and go it can wear...
  11. A

    Hesston 3717 Bearing

    Looking to see if there was an equivalent bearing to match R12240108 (Item 13) say from NAPA or other parts dealer. Thanks
  12. A

    MF 265 Lower Lift Shaft

    Anyone have any tips on removing a stuck/frozen shaft. LH came of ok. RH is being stubborn. Tried AMS penetrating fluid over several days. Tried heating with MAP gas. It will not budge. Thanks!
  13. A

    International Cub Fan Belt Issue

    I am replacing the fan belt on my international cub. The belt I took off is marked 251428R1. I ordered the same belt and received it with packaging indicating the same number. I shouldve checked what was stamped on the belt but I did not and Im upon stalling it it seems a bit too tight where...
  14. A

    International Cub Coolant Outlet Gasket

    I ended up having to remove the coolant outlet elbow to replace the short rubber hose leading to the radiator. As I did not have a replacement gasket or proper type of RTV to replace the old gasket I reused the old one. Now I am getting leakage around the elbow at the head. 1) Should I...
  15. A

    77 International Cub clutch stuck?

    Hello everyone.. After about 6 or seven years of sitting Ive decided to look into a clutch problem on this tractor. We did not use it much and pretty much lived with the slight grinding until it got much worse and parked it. I am not sure about a stuck clutch as this just didnt happen all at...
  16. A

    NH 55 Rolabar Input Shaft Pin

    I am installing a new yoke on the input shaft and curious as how to secure #24. This secures the yoke to the shaft. The old yoke was destroyed and the pin did not have anything to keep it in place. There are two holes on each end and you would think a cotter pin is used but it seems awfully...
  17. A

    NH 55 Rolabar Rake Inout Shaft Yoke issue

    Hello all. After some bearing failure weve had to replace the gearbox bearings/seals on this rake and sorta overlooked some damage to the yoke that slides on the input shaft. This yoke (23) 39361 attaches to the shaft (22) with a through pin (24). Ive tried to find an image of this yoke/drive...
  18. A

    JD LX277 Mower Transmission Pump Shaft repair?

    Is it possible to refit/remold the fit between the pulley and shaft? I can barely go through a season without having to replace the pulley. This will be the third one and getting close to the replacement cost of the shaft. They are few and expensive. It is worn and creating slight play...
  19. A

    NH 477 Haybine input shaft bearing replacement

    This project started out just to replace oil seal (19). In the process of pulling out input shaft (15) the outer bearing (6) came apart. The shaft was pretty snug on the way out and apparently the pulling knocked the roller bearing cage loose. I did back off on both bolts (20) as the service...
  20. A

    NH 477 Haybine over running clutch weld

    I am planning on doing this repair/modification on our haybine. Does anyone have a picture of this fix? Thanks!
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top