(800) 853-2651
SHOP NOW

Search results

  1. F

    Farmall M 5th Gear

    Had a post a while ago about an M that I can’t get into 5th gear. Appreciate all the help. I replaced the pilot bearing and bearings in front carrier as they were pretty bad. The 5th gear looked ok to me ant the time but maybe I don’t know what I anm talking about. Unfortunately I...
  2. F

    Farmall M road gear locked out

    The gear looks like it has no wear. It slides just over the nubbins on the 5th direct gear there and stops before it fully engages. I have had every bolt forward and left of the shifter off. I even took the steering pillar loose to get the one under there. The gear is still not throwing all...
  3. F

    Farmall M road gear locked out

    I have an M that won't quite go into road gear. It barely engages and grinds. Previous owner said it is a 49 corn picker. Said there was a pin in the shift rail. I took the forward inspection cover off. There looks to have been something on the front of the rail ground off previously...
  4. F

    Ford 4000/3000 rear axle preload.

    Here are a couple pics from service manual. It looks like the second has some sort of
  5. F

    Ford 4000/3000 rear axle preload.

    I posted earlier about a Ford rear end in Allis backhoe. My elvasting was cracked badly and I have a new-to-me housing. Unfortunately this requires me to do the bearing preload etc. My plan is to use my bearings as they look fine. I have the service manual and it lists some special...
  6. F

    Allis Backhoe with FORD rear end.

    Yes. I have a C5NN4012E on my axle housing casting. Thank you for the response everyone! I am in MO. Pretty far away from everyone so far. Are the axles on these 4000 series all the same? Do they all have diff lock? Thanks again.
  7. F

    Allis Backhoe with FORD rear end.

    I have an Allis 715b backhoe with what I think is a Ford 4600 rear end. My right housing is cracked pretty much all the way around. I am looking for info to replace axle - if there is an equivalent Ford backhoe or forklift to look for. Ford right housing PN C5nn4012e In searches I am...
  8. F

    1030 Hydraulics - What am I missing?

    I took the o-ring that I had on the poppet off and put it in the bore loose. I also made sure the pilot was going down in the poppet. I don't know what did it but it's working now. The PRV must have been bad to begin with and then I put it back together wrong. Just wanted to give you an...
  9. F

    1030 Hydraulics - What am I missing?

    Yeah there are two O-rings in the bore of the PRV - I remember because they are tricky getting in there. I don't think there is supposed to be one on the piston.
  10. F

    1030 Hydraulics - What am I missing?

    Sorry.
  11. F

    1030 Hydraulics - What am I missing?

    That's what I was thinking, but I'm not seeing a problem. Do I need to look at the PRV insert? How do I get that out?
  12. F

    1030 Hydraulics - What am I missing?

    I'm sure the new CIH Pump is fine. The levers do return to center immediately. Started up once this issue began. The pressure doesn't go directly to 900 it comes up slowly and then holds there. I guess I'll take the remote block apart again, check the relief and pull spools out all the way.
  13. F

    1030 Hydraulics - What am I missing?

    I have a 1030 with weak hydraulics. Shows 900psi at WOT. Remotes and 3pt both weak. I took the remote block off and changed out o-rings on relief valve - nothing broke, looked good. I also took the side caps off and no obvious issues. Took the draft valve off and it looks good - shuttle...
  14. F

    560 ta intall

    Yes clutch and pressure plate installed. Just noticed that it doesn't seem like it is spinning free. It doesn't freewheel at all. I guess I was thinking the clutch might be rubbing on the case but I'm guessing it ought to be torqued against the ta shaft?
  15. F

    560 ta intall

    Gentlemen I am putting a rebuilt ta back in a 560. I think I may have overtorqued the countershaft nut. The one that holds the backside of the clutch. It seems like it is dragging when spinning ta but my manual has not torque value. Anything else I should know for install? Thanks.
  16. F

    1030 Case Hydraulics

    Ok I lied. I found the oring and sleeve in the valve body. I put all new orings and sleeve in relief valve and hydraulics are the same. I bought a gauge and I am making 700psi at WOT. With pressure this low I'm guessing maybe the pump? Is there no chance the DOM shuttle valve causing...
  17. F

    1030 Case Hydraulics

    I don't have an oring or seal ring. May need to pick in the valve body but pretty sure they're gone. I don't know where they went but found the parts online. Thanks.
  18. F

    1030 Case Hydraulics

    1030 has been acting up. A couple times while discing it would stop raising disc. It happened a couple times and I always got it to raise eventually. Seemed like it lifted slow a couple times. Yesterday I started it up cold and the disc only raised a couple inches off ground. Three point...
  19. F

    560 TA Install

    I am about to put a TA back in a 560. Should I be installing new seals/bearings in TA housing. I'm thinking I could do it with sized wood blocks. Also, TA clutch looks ok. Is it generally a good idea to do pilot bearing and refurb pressure plate there? The fingers have some wear but...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top