(800) 853-2651
SHOP NOW

Search results

  1. N

    Oliver pto parts

    Looking for used pto shaft for my 77. Anyone have one laying around?
  2. N

    Kubota mini excavator

    Here’s a question. My travel alarm is driving me nuts. I wanted to see if anyone knew how to cut this out. I can put it on a switch if I could figure out where it even. Is. Thanks.
  3. N

    A fan shaft

    I need help removing fan shaft. I can’t lget the bevel gear off to replace bearing. I got the fa blades etc off the front. Which way does shaft come out?
  4. N

    Aluminum radiator

    folks with aluminum radiators for John Deere’s where can I get one and does the sheet metal bolt up. Or would I have to make custom brackets then, with custom piping etc? Looking for options. Thanks
  5. N

    My A falls on its face

    My 52 A. Idles great. Revs up good. Put load on it. Starts to sput around and falls off fast to stalls. I’ve check valves. Adjust carb all over the place. Any other thoughts? I’m new to deeres Thanks.
  6. N

    Manifold gasket

    question. I have a power block.in my 52 A. Here is my problem. Bought manifold gasket for a late 52 A. Does not fit. Anyone know what I should do here?
  7. N

    B front on A

    Anyone put a B front pedestal on there A for weight differences? I know not direct fit and customization needed. Just asking what all you think all needs adjusted. Radiator/tinwork. Thanks
  8. N

    52 JD A

    Just got a jd a Need some pic ideas to make adjustable hitch ideas. Thank you
  9. N

    Engine builders

    Looking for some help with Oliver engine builder. Any suggestions? Greatly appreciate it.
  10. N

    massey pony plow

    I have been trying to plow with my Pony. it will not plow deeper than 3 to 4 inches. I've adjusted everything that i can think of. I acquired this from a farm i bought. any help would be appreciated. Thanks.
  11. N

    Massey pony plow

    Can anyone help me figure how this thing hooks up? I may be missing some important parts. Thank you
  12. N

    massey pony plow

    I acquired a plow for my Pony. I can not figure how the front hooks to tractor. Got it figured to the back side to the lift arms. can anyone help or pics would help alot. thank you.
  13. N

    Zenith carb

    Question. I am loosing vacuum on my tractor. I have a gauge in the carb and when pulling it. It starts to fall in its face with no vacuum. It starts out at 20psi when light load in engine. It's a 300 cube Oliver. Thx
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top