(800) 853-2651
SHOP NOW

Search results

  1. 5

    MF35 power steering leak

    I have searched this topic and I know there are LOTS of problems with this system. My issue is the power steering fluid is leaking from the cylinder back into the steering housing until it fills the housing then begins to leak the fluid out around the allen head screws that hold the rack in...
  2. 5

    Z134 Carb issue

    Z134 with aftermarket Marvel Schebler look-a-like carb. Runs fine, starts good when cold. But when engine is stopped when hot and then try to restart a couple minutes later it is flooded and loaded up with fuel. I am a carb idiot, which is why is just bought a new one and bolted it on. I have...
  3. 5

    35 seat

    I am slowly restoring a 1961 MF35 diesel. Its NOT going to be all original as I had to replace the engine and I added a power steering box from a salvage tractor. I am interested in what others have to suggest in the way of suspension seats. I have the original but curious if anyone has found a...
  4. 5

    35 perkins diesel fuel filters

    I have a project 35 with the 3.152 engine. No fuel filters were on it when I got it. Can someone give me the fuel filter numbers you use? I have used NAPA filters in the past, but I'm not partial to any brand. I also do not know the oil filter number, so if you have it please share it as well.
  5. 5

    AD3.152 engine swap

    Original A3.152 indirect injection engine on a MF35 project had the crankshaft thrust washers in the oil pan when I took it apart. Block and crank had severe scoring and machine shop guy tells me its trashed. So got a AD3.152 from an industrial MF40 in a salvage yard. I have been told it...
  6. 5

    Perkins A3.152 problem

    The MF35 project I picked up has the Perkins A3.152 diesel and the previous owner ran it while the thrust washers were out of place and in the oil pan. So the block and crank are ruined. Anyone dealt with this. It is not easy to find a replacement complete motor or block. Should I just look for...
  7. 5

    Perkins A3.152 question

    MF35 has an adapter plate mounted on the rear of the engine in between the flywheel and the engine block. On the very bottom of the adapter plate there is a threaded plug which I think is brass. My question is what is the purpose of this plug?
  8. 5

    broken rocker arm

    A3.152 rebuild Ran between 3-7 hours and ran great with no issues then began running rough and smoking. Removed valve cover and found a broken rocker arm. Valve is not stuck as the spring can be pushed down by hand. Lifter is free as well. I read somewhere that this could be caused by the...
  9. 5

    one wire alternator

    MF 35 with Perkins diesel. Anyone have an diagram that an electrical idiot can follow? None of the wiring existed when I picked up this project. Engine has been rebuilt and now trying to sort out the wiring. I will be using a one-wire alternator. However I am 3 levels below novice when it...
  10. 5

    35 power steering conversion

    Has anyone installed this power steering conversion kit? https://www.ebay.com/itm/MF100-Massey-Ferguson-Power-Steering-Kit-for-Model-135/263927422259?hash=item3d734cdd33:g:1EQAAOSwnTBebszy I have an MF35 and was wondering if this kit for a 135 would work on my 35 with the Perkins diesel...
  11. 5

    Parts book

    I just picked up a '61 MF 35 with the a3.152 Perkins. The service manual I have has the rebuild info in it for this motor. However the parts book I have only has the Standard diesel motor. I really like having the parts book with all the exploded views and diagrams. Any suggestions as to...
  12. 5

    Tach drive alternator

    I have an alternator with the tach drive ordered from this website. Does anyone know if it come with the correct size pulley? It says it comes with a pulley, but does not list the size?
  13. 5

    Clear coat?

    Bought red enamel alkyd paint from this website. Tisco brand. Has anyone use a sealer or clear coat on top of this paint? Or suggestions are welcome as to how to finish it off after the last coat of paint. It's on a Ferguson 35 by the way.
  14. 5

    35 power steering

    Got fluid leaking out from the top of the steering shaft. New seals and o-rings were put in during a rebuild and it has been fine this summer until this week. Anyone else had this issue?
  15. 5

    z134 mystery pecking noise

    Here's the story. Crankshaft ground, new main bearings, new rod bearings. Sleeve and pistons were relatively new, I did put new rings on them. Head was refurbished with new valves. Brand new rocker assembly. Valves were set, engine was ran then valves set again to .013. Oil pump rebuild. New...
  16. 5

    Carb issue?

    z134 engine on a 35. New aftermarket carburetor has been installed after a complete engine rebuild. It runs great when started cold, no hiccups when mowing through thick brush and grass. Yesterday running a bush hog I had to stop and talk to a neighbor and it was really hard to start and blew...
  17. 5

    TO35 Hood access panel

    I need to find a replacement knob for the hinged hood panel as it was missing on the TO35 project I am involved in. I have tried to search online using the part number but have come up empty so far. Anyone found a suitable replacement? If so, what was your source?
  18. 5

    35 power steering problem

    Power assist works fine when turning left, but does not work when turning right. Any one else had an issue like this? It is on a TO35. The steering assembly was taken off another tractor and added to this one. So I have no idea if it was working properly before I acquired it. All seals/ o-rings...
  19. 5

    35 power steering help

    TO35 power steering seems to work when turning left, but feels much harder to turn when going to the right. This is on a tractor that is undergoing a complete rebuild. The pump was purchased from a salvage yard and the steering box from a donor tractor and was refurbished with all new seals. New...
  20. 5

    Rear axle end play

    TO35 rear axle end play was adjusted with shims. Without the wheels installed one brake drum is spun and the other turns in the opposite direction like it is supposed to as described in my service manual. My question is involving the change now that the rear wheels have been installed. With...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top