(800) 853-2651
SHOP NOW

Search results

  1. J

    IH 154 PTO shaft bearing

    I am replacing the PTO shaft bearing near the front pulley, IH Part # 549 165 R91 which replaces 491 590 R91. The old one was a 2 piece design. The new one is a little longer, 1 piece design. I can't get the pulley, spacer and new bearing assembly to fit in between the front and rear snap rings...
  2. J

    IH 154 Cub lo-Boy clutch pressure plate

    I think I need to replace the clutch pressure plate 531 708 R11 on my IH 154 Cub lo-Boy. Of the newer ones that use a bolt that tightens the plate onto the shaft ,what is the better style, the cast one from IH or the machined aftermarket one? I am replacing the transmission input shaft .
  3. J

    Gasket Dressing

    I am doing the Pan gasket, final dive pan gaskets, etc. on my IH 154 Cub Lo-Boy and can't remember what I used years ago to dress them. What ever I used worked good (no leaks) but was a bear to get off. I do have some surface scratches so I need to use something?
  4. J

    Will galvanized roofing nails kill a tree?

    I need to put up some boundary markers and was wondering, will galvanized roofing nails kill trees?
  5. J

    Cat 215 starter question

    I need to pull the starter ( last removed in 1988) in a low hour Cat 215 Excavator (3204) that has not run in a couple of years. I took out the three bolts holding it in and it will not budge. Is there a bolt that I am missing or could it be rusted in place?
  6. J

    Diesel Fuel Lubricity additive

    I an going to be converting a Nice Cat D4D that has been run on #2 (I know this for a fact) over to diesel. What should I add for Lubricity? I always run Standardyne in my other diesels but adding something more can't hurt. I was thinking of also adding either Marvel mystery oil, Dextron...
  7. J

    Farmall H Lift-All Drive Dog always loose

    I have posted about this before but am still having the same problem. The Drive Dog that drives the Lift-all Hyd. pump on my Farmall H is loose. I can shake it with my hand and I would assume, over time not being tight, it will cause something to wear out. Background, the Drive Dog was tight...
  8. J

    Update on Farmall H Loose lift-all drive shaft.

    I am thinking that when I used my Lift-All, the round nut never loosened up ( turned counter clockwise) to make the drive shaft a tight fit. I decided to loosen the round nut ( Turn it counter clockwise) with a pipe wrench and now got the drive shaft really tight. I am wondering if I could...
  9. J

    Farmall H lift-all drive shaft loose

    The driveshaft that drives my Farmall H lift-all is loose. I had replaces the seal on the transmission side. You can shake it inside of the couplers. It is starting to get a little worn. Any ideas at a fix? Thanks!!
  10. J

    Oil for a Farmall H Mag??

    What does everyone use to oil a Farmall H mag? I use to use 3 in 1 oil but my cousin gave me some machine spindle oil and was wondering if that would be ok? He uses that spindle oil to oil his Cub distributor felt? Thanks!
  11. J

    15W40 Farmall H air cleaner oil???

    Is it ok to use 15W40 in the air cleaner of a Farmall H? I use IH low ash 30 wt in the engine. Somebody gave me a gallon of new 15W40. Thanks!!
  12. J

    Necessary to polerize a farmall H?

    I replaced my battery in my Farmall H a couple of months ago. It went over the winter. It seems to be charging ok (High and low charge). I didn't polerize the generator, should I do so now? It is 6 volt positive ground. Thanks.
  13. J

    Cadillac web site forum needed???

    I am having some problems with my 1985 Cadillac. Is there a web site/ forum like this one for Cadillac's. Thanks!!
  14. J

    Correct wrench size needed?

    What is the correct wrench size to do the points in an IH Cub IH distributor and a Farmall H mag? I am thinking 11/32". Also, what is the best to use, open end, angled open end or box? Thanks!
  15. J

    Farmall H swinging drawbar and U shaped drawbar question??

    I am looking to replace the drawbar and U shaped drawbar on my Farmall H. The U shaped drawbar was bent in a farm accident and by using the drawbar extension plate clamping the swinging drawbar down instead of a strap on the swinging drawbar. My swinging drawbar is a few inches shorter because...
  16. J

    Cub distributor felt oil?

    What oil do you use to oil the felt under the roter of a Cub distributor? The manual says light engine oil so can I use 30 wt? Thanks!
  17. J

    Farmall H Trans and stearing oil GL-1or GL-5?

    On a farmall H, does it matter what 85,90-140 oil is used in the transmission and stearing gear, GL-1 or GL-5?
  18. J

    Good knock -off HVLP Gun????

    Is there a good knock-off HVLP gun that can do high end work? The reason I am asking is that I am thinking of getting a HVLP gravity feed gun to cut down on over spray. After not using my existing guns ( Sharp and non HVLP gravity feed Devilbis) for a few years I had a small painting job last...
  19. J

    Mini Butane torch

    I am looking into getting a mini Butane Torch. They go to 2,400F. Are they any good say to use on a rusted bolt? I have a regular cutting torch and an aceletene B tank torch but was thinking a mini Butane Torch bight be easier than draging out one of those for a quick job. Thanks.
  20. J

    Solvent Question

    I was wondering what people use for a cleaning solvent in the shop to clean small things. Not to use in a parts washer but to use to clean grease/oil. Example, have to clean off the oil around a filler plug before checking or grease on a screwdriver. I have been using an auto body prep...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top