(800) 853-2651
SHOP NOW

Search results

  1. O

    Average age of user

    69 John
  2. O

    Did I make the wrong decision?

    I've seen people die from metastatic prostate cancer. If the shots can lengthen the time you are (mostly) symptom free, then I'd take the shots. I'm already old and weak. I'm not quite 70. You did well to do as good as you were. None of us are getting out of this life alive. My Dad made it...
  3. O

    Infection from my cow pasture

    Since you haven't gotten better...PLEASE ask your doc to send you to an Infectious Disease Specialist ASAP (before you lose your toe or foot)! You may need to take several different antibiotics every day. Or you may need IV antibiotics to kill it. The right answer depends on multiple...
  4. O

    401, It Lives, Need a Wiring Harness

    Steiner, in Owosso, Michigan sold me an excellent harness for my 4020, as well as idiot proof instructions of what gets connected to what. John
  5. O

    4020 wiring harness

    I bought a complete wiring harness for my 1964 4020 from Steiner this past spring. Excellent quality. With included directions, it was easy to install. Steiner asked me the year of the tractor (serial number), and they wanted to know if tractor was 24 or 12 volt, alternator or generator. Can't...
  6. O

    Electrical Connectors for JD 4020

    I received top quality wiring harnesses thru Steiner (in Michigan). I highly recommend. John
  7. O

    Gas 2020 Wont Start

    My 2020 ran terrible. Pull the fuel line at the carb. There is an in-line fuel filter on the end of the fuel line! (It actually sticks into the carb.) My filter was plugged and letting very little fuel past it. Cleaned it out, and now it runs much better. John
  8. O

    1967 John Deere 2020 gas engine running issue

    Mine wouldn't run well until I discovered the fuel line screen on the end of the fuel line (actually sticking into the carburetor). Cleaned out that screen (it was full of junk), and it ran much better. John
  9. O

    who raises livestock on here ?

    7 Beef cows, a milk cow, 30some chickens, 2 bee hives, usually a couple pigs.
  10. O

    John Deere 2020

    If you don't have a lot of mechanical aptitude (like me), it can be miserably annoying until you get all the bugs worked out. Mine is a 1967 model, and is now a good little tractor (55 horse). If you buy, get an Owners Manual, a Repair Manual, and a Parts Manual. John
  11. O

    poll on using sisal twine in balers

    Deere 328. I prefer Sisal, but the baler will do either. John
  12. O

    Houser and Sons

    They're about 10 miles south of me. Have bought two tractors from them. They will honestly tell you what is right (and wrong) with the equipment you are buying. Albert has had some health problems lately and is not as involved in the business. Todd (son) is now very busy, but is also a good...
  13. O

    2020 JD

    If it is a gasser: Unscrew the fuel line from the carburetor. There is a strainer on the end of the fuel line (the strainer sticks into the carburetor). My strainer was pretty well plugged with crud, and the engine wouldn't run worth beans. Cleaned out the strainer and it runs like a top. John
  14. O

    John Deere 2020 final drive oil

    Check the oil level by unscrewing the knob (which is attached to a dipstick) that is on the platform - directly behind you right heel when you are sitting on the seat. After you have the dipstick loose and dried off, then just set it on the access hole to read an accurate level (assuming the...
  15. O

    John Deere Grain Binder

    It's been about 12 years since I used mine (don't trust my memory) but: My recollection is that the "hitch" is a triangular framework that (when in working position) mounts in front of the binder. When in transport position this triangular framework mounts in brackets underneath the grain...
  16. O

    JD 1020 Front Wheel Reversal

    I'd say the way you have them is the way they are supposed to go. Certainly would cause no harm. John
  17. O

    4010 High Oitch Steering Noise

    Loose belt?
  18. O

    IH Model 15 Hay Rake Parts

    I have an IH #16 Hay Rake. My bearings look identical, except may be a hair smaller (for instance: largest diameter is 1 & 15/16 instead of 2 & 1/32). Middle diameter on mine is 1 & 7/32, small diameter is 3/4 inch. Try part number ST437. Mine were readily available from IH last time I ordered...
  19. O

    JD light grain binder

    Write a letter to: Midway Repair Shop, 14400 Dover Rd., Dalton, Ohio 44618. Tell him exactly what you need and how many of each you want. Enclose a picture if needed. He sends me the parts, and encloses a bill (and trusts you to pay it - please do). He is in the middle of Ohio's Amish country...
  20. O

    Mc Cormick hammer mill (feed grinder)

    Yes! If it is near Ohio, I would be interested. John
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top