(800) 853-2651
SHOP NOW

Search results

  1. J

    Truck tractor Auction

    Famous Chicagoland tractor and truck museum auctioning its multimillion-dollar collection https://www.foxnews.com/auto/famous chicagoland tractor truck museum auctioning multimillion
  2. J

    chuck machinist coupling pic for you

    .
  3. J

    Former Case dealer for Don

    This was the only Case dealer within 100 miles of me. Grandpa Jennings told me more than a few times he was going to kiss off Case and start selling smaller tractors that were more suitable for the area changing to small farms and bedroom community for Seattle and the urban spread. I happen to...
  4. J

    Re: Looking for 1958 CASE 400 PTO clutch replace/repair adv

    I use this garden digger tool like the pic to pull out the adjustment pins, if you put a slight bend in the shaft down near the fork it works out great. If the clutch is hot for an extended period, the discs may be warped so do your tightening adjustment one slot at a time and test or you may...
  5. J

    116-year-old tractor sold $425,000

    https://www.foxnews.com/auto/important 116 year old tractor sold for record 425000
  6. J

    OH Mike .. Re: Wanted: Case 430 PS control valve

    There was a glitch between the Classic and Modern forums My response to your post is at this link. Joe http://www.yesterdaystractors.com/cgi bin/viewit.cgi?bd case&th 317150
  7. J

    Re: Wanted: Case 430 PS control valve

    I can address this cylinder only as it is mounted on Case wheel tractors. I don't know if you have the identical cylinder on your forklift, that is something you will have to determine by these pics. First some questions, did you have equal wheel swing in both directions before the seals...
  8. J

    Marvel Schebler Carb Floats

    Some info & video on large and small bowl floats. Joe https://www.carburetor parts.com/Marvel Schebler Floats_ep_430.html
  9. J

    Zach81 530 PTO

    Zach, after much research and assembling pics for posting I have not been able to tie the standard PTO with the 530 shuttle. It may be for the 530 triple range only? My PTO experience is with the 300/300B series and one 430, all had triple range. I don't have any shuttle experience. Pic is the...
  10. J

    Testing

    Haven't been able to post for a week or so. Kim has put in a fix. Thanks Kim! Joe
  11. J

    ACG .... PTO pump drive.

    Loren, Read your comment on Ol'TinBender's post. I didn't want to hi-jack his post by adding this there. I don't have the original Case shaft with a spline on each end. I think the hub is original though. I had a new spline end matching the hub welded on to the shaft. They did a socket weld...
  12. J

    CKRICHARD

    Apparently my response to your e:mail address as listed on the YT response is not going through. It appears that part of your e:mail address on the YT message has a miss spelling, gmial as opposed to gmail??? Send me an e:mail to [email protected] Joe
  13. J

    CKRICHARD PS bracket

    If you haven't found a torque generator bracket, can you use one like this? This bracket fits 311 thru 611B tractors. It doesn't look like the one on the Case parts site for 430 but if you have a side rail like in the pic it should work. e:mail is open. Joe
  14. J

    PTO shaft seal

    My "56 310 has been migrating about a gal of hyd oil into the transmission a year. It is up to about 3 gals this year so figured I better get off my duff and change the shaft seals. Hitch piston is not leaking. I don"t have the time or desire to split the tractor just now so I pulled the eagle...
  15. J

    310 utility clutch

    New one on me. The clutch wasn"t releasing all the way, grinding gears on shift. Got progressively worst. Release yoke pivot was worn and cracked open on one side. Joe
  16. J

    RGV hay 310B PS cylinder

    In rereading your post, if not a typo, it appears you have the supply and return ports mixed up. Try your air test using the supply port, pressure will push the relief ball tight against the seat in that direction. The relief is a pressure differential check valve. There is no spring, the ball...
  17. J

    The Original Sin.

    Posted without comment.
  18. J

    steven in tn ... VAC distributor pic

    You're likely well past needing these pics. The tractor front is way high & I did a poor job on camera angle so the line is ballpark 3 0'clock looking down on the dist. PIC 1. My '53 timing mark _____DC. Yours may differ pending year. Pic 2. start gear mesh about 4 0'clock or slightly past...
  19. J

    Re: Case 300 tractor hydraulic level

    Torque tube: Some posters are using 10-30 motor oil. I am using a general purpose hydraulic oil with ~10w viscosty. Transmission: I am using 89-90 gear oil. Joe
  20. J

    Re: TSX-635 Carburetor Replacement

    It's really tough to drill these nozzles out as they thread in two places. You might get lucky if the LH bit grabs and turns it out, otherwise cleaning the remains out of the bottom threads is nearly impossible. Worth a shot though, good luck. let us know how it comes out. Joe
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top