(800) 853-2651
SHOP NOW

Search results

  1. P

    Wanted Wanted - International TD-9 or WD-9 Diesel Engine

    Looking for a good International TD-9 or WD-9 diesel engine. I need to change out a bad engine in a 1948 TD-9 crawler. I believe it is a Series 91, D-335 4 cylinder "gas start" diesel.
  2. P

    WD-9 Engine Fit TD-9 Crawler

    Will a WD-9 diesel engine fit a 1948 TD-9 Crawler?
  3. P

    TD9 Main Bearings (1948 Diesel Crawler)

    Is there a source of engine main bearings (.010) for a 1948 TD9 diesel crawler? Working on a 1948 TD9 and am trying to find engine parts. A good .010 bearing part number would help too. Thank you.
  4. P

    Power Steering on a Minneapolis Moline GB?

    Has anyone ever added power steering to a GB? If so, how did you do it?
  5. P

    Power Steering on a Minneapolis Moline GB?

    Thanks for the help. I will see what I can do. I like the tractor but the steering is becomming too much.
  6. P

    Case Farm Machinery Sign (Original)

    A friend of mine would like to sell his original Case Farm Machinery sign. The sign came from a dealership in central Kansas. The sign has some bullet holes and measures 71-3/4 inches long and 30 inches wide. Does anyone know an approximate value of the sign?
  7. P

    Vacuum Coming Through Vent Behind Seat (Hydrovac Questio

    I have a 1962 GMC with a hydrovac brake system. Is there supposed to be vacuum coming through the breather behind the (drivers side) seat? I have vacuum through the breather during normal driving without braking. The brakes do work great.
  8. P

    Farmall H Magneto Question (American Bosch MJB4A-308)

    Thank you.
  9. P

    Farmall H Magneto Question (American Bosch MJB4A-308)

    I am not sure. If that is what is needed, I can take the mag to a shop and find out. I like having mags so I don't have to keep a collection of batteries. These are just show / play around tractors. A friend was cleaning a shed and found the mag and gave it to me. Thanks.
  10. P

    Farmall H Magneto Question (American Bosch MJB4A-308)

    Will an American Bosch MJB4A-308 work on a Farmall H? I have the same American Bosch magneto on my Farmall M and it runs great. Thanks.
  11. P

    Will a LA Case Power A Log splitter?

    I recently picked up an LA Case with hydraulics. This is just a hobby tractor that I keep in town. I was wondering if an LA had enough hydraulic power to run a log splitter? I usually run other tractors on the splitter, but if the LA had enough hydraulic pressure, I will split wood with it this...
  12. P

    560 Hydraulic Problem

    I am working on a Farmall 560 Diesel. The tractor had set out for some time. I got the engine running and cannot get the back hydraulics that raise and lower the drawbar to work. The tractor is full of hydraulic fluid and the power steering works. Any ideas? I am sure something is froze up...
  13. P

    Farmall 560 Diesel Fuel Return Elbow Help

    Thanks for the help. If I make an extension and need a little back pressure I can always pinch it a little.
  14. P

    Farmall 560 Diesel Fuel Return Elbow Help

    Someone took the check valve off the elbow assembly (370676R92) on a 560 Diesel fuel tank. Water got in the injector pump through the return line and ruined the pump. I want to put an extension on the elbow so water and sediment will not get into the return line again. Check valves are about...
  15. P

    JD 4020 LP Cuts Out After 45 Minutes Of Use

    I am working on a JD 4020 LP. We installed electronic ignition, used resistor plugs (gapped at .015) resistor plug wires, rewired the tractor, tried 2 new coils, new ballast resistor (because someone put a different ignition switch on the tractor without the built in resistor), cleaned the fuel...
  16. P

    Is Precup Removal Necessary - 560 Diesel?

    I have a 560 diesel with a D282 engine. The injector pump and injectors will be removed and rebuilt. I read several posts about precup removal. That sounds like a hit and miss. Is it necessary to remove precups or should they be left alone? Looks like the precups are expensive if I would...
  17. P

    560 Injector Pump Removal Question

    I need to get the Roosa Master injector pump on my 560 (282D) rebuilt. Due to the risk of seal damage during installation, is it best to take the shaft out and send it with the pump for the rebuild? If the rebuilder can install the shaft during rebuild, can the pump be installed (shaft in pump)...
  18. P

    12 volt System to 6 volt Coil (What Ballast Resistor)?

    Thanks for the help everyone. I now have a good direction.
  19. P

    12 volt System to 6 volt Coil (What Ballast Resistor)?

    If that looks about right, would you put a resistor in front of that coil or wire the coil direct 12 volts?
  20. P

    12 volt System to 6 volt Coil (What Ballast Resistor)?

    The coil I am looking at is a NAPA 6 volt BK S61548 (S.61548). I cannot find a resistance.
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top