(800) 853-2651
SHOP NOW

Search results

  1. E

    Replacing gasket on shuttle transmission on a 320 1957 case industrial

    How to replace the shuttle clutch cover on a 1957 320 case industrial
  2. E

    Replacing transmission cover for shuttle gears and high low range

    This is being discussed. I replaced the cover hasjyvwith permatex, would like to replace cover with proper gasket
  3. E

    front tire size for a 1953 for jubilee

    Front tires on my 1953 are 6-50 x 16 Will 6-50 x 16 8 ply rib tires work for my ford Jubilee?
  4. E

    comparison of the kubota 2019 bx23s 1957 CASE 320 INDU

    wanted to know comparison of the digging power, lifting brush onto a burn pile, my case has homemade fixed thumg
  5. E

    water leak in a fordson major diesel tractor

    Helping a friend with his fordson major diesel tractor. Tractor hasn't been run for years. Started but has a water leak into the base. I wanted to know: Are these diesel engines wet sleeves? I suggested removing the pan and looking to see if a water leak could be seen around one of the...
  6. E

    Checking oil transmission and differential 8N

    Fill plug on top of transmission and dip stick on right side of differential, Is the oil common to both transmission and differential?
  7. E

    ford jubilee: two fill ports: one on top of transmisison

    My ford Jubilee has a dip stick on the right side of the differential. Does this dip stick measure oil for both the transmisison and differential? Is there a bolt to remove to check oil in the transmisison? Both units use same oil? Chris
  8. E

    level plug for transmisison on my 1952 8N

    Would like to know where the level plug for oil in the transmision is located. Fill port on top of transmision. Differential has dip stick to check oil level.
  9. E

    Lock tab for adjuster ring on my 1951 td6

    The adjuster for the adjuster ring on my 1951 TD 6 had a damaged end on the small adjuster plate Could I make something to replace it?
  10. E

    adjusting stuck clutch on my 1951 td 6

    Several people on the forum have given me suggestions which I appreciate. Removed small cover plate and sprayed things under the cover with blaster. Will use my 9/16 end wrench with a wire attached to it in case it slips out 0f my hand to loosen the adjuster lock Is it neessare to remove the...
  11. E

    removing and replacing clutch on my 1951 TD6

    My TD 6 sat for a year, it was covered. Clutch lever too hard to operate. I had left the clutch disengaged. Will try to adjust the clutch through the round inspection cover. I know about the bolt and lock to adjust the tension -rockford over center clutch What I want to know: Have worked on...
  12. E

    Replacing transmission cover for shuttle clutch

    Had to get a person to help me. He aligned d he fold and I held the cover Must be a better way you. Cover on my 320 case industrial has theshifter for high and low range
  13. E

    key size for shuttle shift lever on a 1957 case industri

    The main shifter lever for the shuttle clutch on my 1957 Case Industrial. The roll pin broke in the shifter lever. Would like to know the key size and roll pin size if anyone has a parts manual for the tractor.Looks like a 1/16 spring roll pin { removed what was left of the roll pin}. Key is...
  14. E

    1957 case 320 loader backhoe

    Have the opportunity to sell my case 320 loader backhoe tractor. It is in excellent shape, new tires, hydraulic hoses, Looking at a small compact Kubota 23 with loader and backhoe. I adapted a 14 inch bucket from a bobcat to my case. It has a 16 inch originial bucket. Main reason for making a...
  15. E

    pony motor 1939 Caterpillar D2

    What is the number one cylinder on the pony motor? I think number one is on the left side of the pony motor sitting in the seat and looking towards front of the crawler
  16. E

    Lifting rear axles ford 8N is o work on brakes

    I use my logging Jack to lift rear axles to work on brakes Any way to modify a standard automotive hydraulic Jack to lift rear axles? Height of axles is the problem. Same issue for my JD tractor (850) and IHC tractors
  17. E

    fuel pump ford 860

    what is the brant, type of diesel fuel pump on ford 860
  18. E

    size of pipe plug on the hydraulic pump of a ford 3000

    Tractor is a ford 3000 with a 3 cylinder diesel. Would like to bleed the hydraulic system. Tractor is a 100 miles from where I live. Would like to bleed the hydraulic system. Want to use a hose barb with a piece of clear plastic hose to start tractor run it and remove air from the system. Will...
  19. E

    hydraulic pump ford 3000

    Recently purchased ford 3000. 3 point hydraulics not working and has been used to pull things on the farm only for two years. Drained oil from differential filled with correct fluid. 3 point works barely. We think the hydraulic pump needs replacement or repair. Have a tisco repair kit...
  20. E

    procecures to remove the differential plug ford 3000

    We have tried many things. Want to drain the differential and add new fluid. Working on the hydraulics for the three point. Have used heat, the plug has a square head, vice grips, pipe wrench. Concerned about taking the corners off the plug then we will have a round head on the plug. Would...
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top