Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

hydraulics on 444 international


 
Post new topic    
View previous topic :: View next topic  
Author Message
Judy Teets
Guest






Report to Moderator

PostPosted: Mon Feb 15, 2010 4:47 pm    Post subject: hydraulics on 444 international Reply to specific post Reply with quote

Hi , my family purchased a used 444 international with a loader on it. The hydraulics sound terrible on it. I have looked countless times for the fill hole to check the fluid. I have also had several who were familiar with International tractors look and we canít find a dipstick or a fill hole. Now the bucket will not work at all. Can you steer me to some info on the info I need to check the fill level and where it and the fill is? Thanks Judy
 
Back to top
Owen Aaland
Tractor Guru


Joined: 14 Feb 2007
Posts: 3799
Location: Zumbrota MN

Report to Moderator

PostPosted: Mon Feb 15, 2010 5:33 pm    Post subject: Re: hydraulics on 444 international Reply to specific post Reply with quote

The hydraulic fill/check plug is behind the seat in the right rear corner of the casting that the seat is mounted on. Fill to the bottom of the filler plug opening. Make sure loader is down when checking. Capacity should be three gallons. The drain is is located on the back side of the same housing just below the fill opening.

If the tractor has been fitted with a crankshaft driven front pump then there will be two hydraulic lines under the seat and the transmission serves as the hydraulic reservoir.
 
Back to top
View user's profile
judy teets
Guest






Report to Moderator

PostPosted: Mon Feb 15, 2010 6:45 pm    Post subject: Re: hydraulics on 444 international Reply to specific post Reply with quote

Thanks Owen, I think that it must have the crankshaft driven pump. It has a pump mounted in the front of the tractor, that is driven by a shaft. We'll see if we can figure it out now. judy
 
Back to top
IH2444
Tractor Guru


Joined: 13 Dec 2004
Posts: 3847
Location: East Central Kentucky

Report to Moderator

PostPosted: Mon Feb 15, 2010 8:08 pm    Post subject: Re: hydraulics on 444 international Reply to specific post Reply with quote

Ahh is yours a 2444? Does it have a foot pedal?
Does it have a big line from the loader valve going back to the lift box behind the seat, right side if I recall? Also does it have a small round filter housing in front of the gearshift?
You may have a 2444, which is the industrial 444.


If so you are likely using the tranny sump for your loader and aux pump. The tranny check level is on the right of the gearshift. remove the plug and fill till 6 inches below fill opening.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters