Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Oliver 77 shifting problems


 
Post new topic    
View previous topic :: View next topic  
Author Message
jddrawbar
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 3:47 pm    Post subject: Oliver 77 shifting problems Reply to specific post Reply with quote

Picked up a nice 77 off ebay this morning. Runs good, but doesn't want to go into the bottom gears of the transmission. It shifts into R2,6th,3rd,&4th....but doesn't want to go into R1,5th,1st,&2nd. Any idea on what could be causeing this? Thanks in advance for any HELP..

 
Back to top
Jeff Oliver
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 7:08 pm    Post subject: Re: Oliver 77 shifting problems Reply to specific post Reply with quote

More detail on "not going in gears" please. As in does it not want to go into the slot or it doesn't pull when in those gears?

 
Back to top
DEH
Guest






Report to Moderator

PostPosted: Tue May 01, 2007 7:36 pm    Post subject: Re: Oliver 77 shifting problems Reply to specific post Reply with quote

Are you saying that you can't get your transmission to shift from HIGH RANGE neutral to LOW RANGE neutral? My 77 seems to have the same problem. I flushed to transmission good with diesel fuel,removed the mechanical lift cover,examined the rails,forks,bearings and gears-everything looked good. So with the cover off and shift lever out of the transmission everything worked good. Could shift into all gears and both neutrals easily. Put everything back together and it wouldn't shift right.Now I'm wondering if there is something wrong with the ball at the lower end of the shift lever.I know this is not an answer but maybe some out there can help both of us. See my posting "Oliver 77 Transmission Shift Lever" Dated 4/24/07


 
Back to top
SPT
Guest






Report to Moderator

PostPosted: Wed May 02, 2007 5:40 am    Post subject: Re: Oliver 77 shifting problems Reply to specific post Reply with quote

Had same problem somewhat with 88, pulled gear shift lever and noticed that alignment pins that are spot welded to shift lever had broken loose. Re-welded alignment pins and shifts like brand new.

 
Back to top
rrlund
Guest






Report to Moderator

PostPosted: Wed May 02, 2007 6:03 am    Post subject: Re: Oliver 77 shifting problems Reply to specific post Reply with quote

I'm guessing somebody had it out and didn't get it back in right. I did that once. Sorry I can't be more help,it's been a while since I've messed with one,but pull the shift out,being careful not to drop those springs,see that everything is lined up,J Schweibert or somebody will have a better memory of what it should look like in there than I can remember. I wouldn't worry too much about it being a major problem,I think it's just in wrong.

 
Back to top
jddrawbar
Guest






Report to Moderator

PostPosted: Wed May 02, 2007 6:13 am    Post subject: Re: Oliver 77 shifting problems Reply to specific post Reply with quote

It doesn't want to slide down the long neutral into the bottom gears.....top gears it hits fine.

 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters