Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Pistons for stroker M crank


 
Post new topic    
View previous topic :: View next topic  
Author Message
Kenny Chinsey
Guest






Report to Moderator

PostPosted: Sun Apr 22, 2007 10:23 am    Post subject: Pistons for stroker M crank Reply to specific post Reply with quote

I am needing advice on what piston will work with a 5 3/4 stroked M crank. I will be using stock M rods and looking for 4 1/8 bore size. Any thoughts or ideas would be appreciated.

Thanks

 

Back to top
trulyred
Guest






Report to Moderator

PostPosted: Mon Apr 23, 2007 2:20 pm    Post subject: Re: Pistons for stroker M crank Reply to specific post Reply with quote

I have a set of used M&W AP75 large pin that are 4 1/8 and have been modified for more compression.


 
Back to top
turbos10
Guest






Report to Moderator

PostPosted: Mon Apr 23, 2007 3:16 pm    Post subject: Re: Pistons for stroker M crank Reply to specific post Reply with quote

I had Murphys Motor Service build a set of pistons for my M. They are really nice pieces cut from Arias forging.

 
Back to top
ChadS
Guest






Report to Moderator

PostPosted: Thu Apr 26, 2007 6:45 am    Post subject: Re: Pistons for stroker M crank Reply to specific post Reply with quote

Well, you can get you a set of 450 pistons, and whack off the material to make them clear, you can also drop the wrist pin location down a little, and not have to remove so much off the pistons. Cyl head choice,,, 450 head, or a 8060 gas head clearenced for the bigger domed pistons. Would run good on E85 with some pump gas to tame the E85 down, but, its not 10 dollar a gallon fuel. I have kits made to spec for up to 6.125 for 4-1/8th bore. Chad

 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters