Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

BIG SON .SORRY I MISSED THE CHALLENGE in ms.


 
Post new topic    
View previous topic :: View next topic  
Author Message
piston
Guest






Report to Moderator

PostPosted: Mon Apr 23, 2007 6:15 am    Post subject: BIG SON .SORRY I MISSED THE CHALLENGE in ms. Reply to specific post Reply with quote

BEEN GOING AROUND UP HERE IN MISSULA, GETTING ALL TECHED UP READY GO PULLING, WILL BE ON THE(PULL)challedge in may, couldnt remember if one l or two, you know i dont make excuses, the rain or few detrails like selling tractor would not stop me being there to defend honor P.S I AM NOT RETIRED EITHER

 
Back to top
Justa Poor Ole Puller
Guest






Report to Moderator

PostPosted: Mon Apr 23, 2007 1:49 pm    Post subject: Re: BIG SON .SORRY I MISSED THE CHALLENGE in ms. Reply to specific post Reply with quote

Im my opinion the pull at Holly Springs was a big mess! Phil Smith and the other guys at Dixie Iron are all good people and fine pullers to be around but their sled is a mess! Additionally their rules have some major problems: Pulling in specific gears is not fair when you have Olivers and M's with changed rear end gearing which makes them faster than the other Tractors in the same gears who can't afford these high dollar modifications, also most of them are violating the RPM rules something awful. If you have "open" or "outlaw" tractors then stay in your classes or don't pull! The only solution is SPEED LIMITS which negates the advantage these rule breakers have.

Mr. Clark told me that the MSFW would be adding speed limits at their MD pull plus adding OPEN CLASSES for the ones who want to go fast. That is the only solution to the situation!

I am not whining or trying to talk bad about the Dixie Iron people. However, facts are facts and no one can refute what I have said in this response as not being true.

 

Back to top
the real CONFEDERATE
Guest






Report to Moderator

PostPosted: Mon Apr 23, 2007 5:40 pm    Post subject: Re: BIG SON .SORRY I MISSED THE CHALLENGE in ms. Reply to specific post Reply with quote

As they say and I agree If you can't run with the big dogs stay on the porch and let you mama lick your wounds over losing that $4.00 trophy.

And as always I don't mind people knowing who the real Confederate is and if you don't like what I say Sonny Daniels is the name and the number is 901-461-4373.

 

Back to top
FARMALL PULL
Guest






Report to Moderator

PostPosted: Tue Apr 24, 2007 7:31 am    Post subject: Re: BIG SON .SORRY I MISSED THE CHALLENGE in ms. Reply to specific post Reply with quote

Justa Poor Ole Puller
I hate that you feel that way about me and the Dixie Iron Club. We put on 10 to 12 pulls each year, and deal with a lot of good people and pullers. Sometimes you can't please everyone. If we have that many UNPLEASED people, it is hard for me to see how we have 150 plus hooks each pull. I CAN NOT control what problems we have with the sled. We do the best we can with what we have to do with. If you need to talk to me personally about the problem you had or are having with me or the Dixie Iron Club, You know my name and my phone number is 662-538-2050. Sorry you feel the way you do, I hope you can find a place to pull where there is no problems with rules or the sled.
Phil Smith

 
Back to top
Lindley Clark
Guest






Report to Moderator

PostPosted: Tue Apr 24, 2007 7:52 am    Post subject: Re: BIG SON .SORRY I MISSED THE CHALLENGE in ms. Reply to specific post Reply with quote

Phil
You and Mr Daniels apparently have taken my comments out of context. The first thing I said was I have no problem with you or anyone else in the Dixie Iron Club. I was merely stating my opinon about the rules about pulling in specified gears rather than having speed limits.

I am sorry I have insulted you and Mr Daniels. Apparently this forum is only for joking around and not stating opinions, therefore I will never post again.

Thank you and Dixie Iron for the hard work with the pulls.

 

Back to top
piston
Guest






Report to Moderator

PostPosted: Tue Apr 24, 2007 11:08 am    Post subject: Re: BIG SON .SORRY I MISSED THE CHALLENGE in ms. Reply to specific post Reply with quote

PLEASE CLOSE MY CAN WORMS

 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Pulling All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters