Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Super Dexta 3 Point Height


 
Post new topic    
View previous topic :: View next topic  
Author Message
Jeff NWOH
Long Time User


Joined: 05 Mar 2009
Posts: 723


Report to Moderator

PostPosted: Thu Aug 10, 2017 8:39 pm    Post subject: Super Dexta 3 Point Height Reply to specific post Reply with quote

Does the 3 pt hitch on a dexta run lower overall than other tractors. My lift arms are maybe 3 or 4" off the ground at the lower limit. The problem is they don't go high enough to get a "normal" implement off the ground.

I've tried a ford 2 bottom plow and it barely gets it high enough to clear unlplowed ground. Also tried a "new" brush hog today and it gets high enough to cut, but won't get it off the ground. It seem to have a decent range and no issues raising up, it just doesn't go high enough.

I used to have mower that I put a set of pins lower down so I could use it on the dexta, but the dexta hasn't been on brush hog duty since I got a Massey Ferguson with power steering. Actually, the mower I've been using on Massey has had the pins swapped with a couple lower bolts, so maybe it's not an isolated issue or the previous owner had a dexta also?

From what I can see in the it manual, the rockshaft is keyed so it's not like the lift arms are just out of time. Is there that much adjustment inside on the linkage somewhere or is this just the nature of the Dexta?
 
Back to top
View user's profile
WayneB
Long Time User


Joined: 07 Nov 1999
Posts: 585
Location: Lunenburg, VA

Report to Moderator

PostPosted: Mon Aug 14, 2017 6:03 am    Post subject: Re: Super Dexta 3 Point Height Reply to specific post Reply with quote

I have several Dexta tractors. One I had, would not go as high as others. Otherwise, the lift was strong and fast. The bottom line is the adjustment linkage was worn.
 
Back to top
View user's profile Visit poster's website
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Fordson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters