Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Gehl MIxer Gear Box Universal


 
Post new topic    
View previous topic :: View next topic  
Author Message
Earl T
New User


Joined: 02 Sep 2014
Posts: 15


Report to Moderator

PostPosted: Wed Sep 13, 2017 3:35 am    Post subject: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

Looking for how people have taken these apart. Looking for tips or what not to do.

 
Back to top
View user's profile
NY 986
Tractor Guru


Joined: 05 Mar 2009
Posts: 3930


Report to Moderator

PostPosted: Wed Sep 13, 2017 5:51 am    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

Do you have your replacement parts all ready to go? Looks like you will have to burn the joints out via a torch. It does not look like it will press apart. If need be you could go to your local parts supplier and come up with yokes and joints. Then cut and key a shaft to join the two assemblies. Take measurements before cutting or pressing anything.
 
Back to top
View user's profile
paul
Tractor Guru


Joined: 25 Dec 1997
Posts: 23498


Report to Moderator

PostPosted: Wed Sep 13, 2017 6:56 am    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

If it was assembled, it can be pushed apart.

If it was welded together as one unit, it will need to be replaced as one unit. (Or made from scratch as you suggest.) They usually don't like to weld that close to a bearing, so I would guess there is some way of pressing it apart, maybe a few hidden clips under some grease or hidden in grooves.
 
Back to top
View user's profile
NY 986
Tractor Guru


Joined: 05 Mar 2009
Posts: 3930


Report to Moderator

PostPosted: Wed Sep 13, 2017 7:17 am    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

Normally, I would say yes to pressing apart but the "cross" is right tight to the yoke from what I see. Usually, for disassembly the cross has to slide towards the yoke to get the cap to move. I don't see from that picture where any clips come into play. Yes, heat and needle bearings do not mix so maybe the caps are peened in for assembly. It looks like he will have to come up on both shafts for a home made assembly so hopefully there is room along with solid true material that has a keyway. It's all going to depend on what can be found for parts. I am thinking that there are very few if any of those joint assembly's laying around any more given the situation with Gehl. But maybe somebody here knows something and I certainly would not mind learning something new in terms of a parts source.
 
Back to top
View user's profile
el6147
Long Time User


Joined: 07 Jun 2012
Posts: 500


Report to Moderator

PostPosted: Wed Sep 13, 2017 2:09 pm    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

Those are press in joints, Calhoun built fertilizer spreaders that used a single joint similar to that(maybe the same) that powered the spinner gear box. I believe that I have some new kits. email is open.
 
Back to top
View user's profile
JD Seller
Tractor Guru


Joined: 11 Mar 2009
Posts: 14627


Report to Moderator

PostPosted: Wed Sep 13, 2017 3:30 pm    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

The pins are pressed into the yoke and pivot in the center section. These usually are not repairable. IF you can get a kit for it then you cut the old pin with a hack saw between the center and yoke. The after you have removed the center you take a punch and knock the pin OUT of the yoke. Notice I said out of the yoke not TOWARD the center. The new pins come with a knurled section that is pressed into the yoke.
 
Back to top
View user's profile
TASO
Regular


Joined: 26 Apr 2012
Posts: 94


Report to Moderator

PostPosted: Wed Sep 13, 2017 5:51 pm    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

These are not easily rebuilt. German-Bliss in Iowa still has a large inventory of Gehl parts. Google them and check out their inventory. I replaced mine on my old Gehl 95 and the new ones are rebuildable.
 
Back to top
View user's profile
Earl T
New User


Joined: 02 Sep 2014
Posts: 15


Report to Moderator

PostPosted: Mon Sep 18, 2017 7:22 am    Post subject: Re: Gehl MIxer Gear Box Universal Reply to specific post Reply with quote

I was able to order a cross kit from Gehl. The cross kit was 43.00 a piece, but that was cheaper than buying the hole assembly for 320.00 I was able to press a pin o thru the center to push the opposing pin out and that aloud it to come apart. Had to use a little heat on a couple of the them. Just like somebody else had mentioned the new pins are knurled to fit tight in the yoke upon reassembly.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters