Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Allis Chalmers 433T Timing


 
Post new topic    
View previous topic :: View next topic  
Author Message
Rocko93
New User


Joined: 14 Nov 2017
Posts: 1


Report to Moderator

PostPosted: Tue Nov 14, 2017 8:45 am    Post subject: Allis Chalmers 433T Timing Reply to specific post Reply with quote

Hello, I am new to this forum and am looking forward to using it. I have a Gleaner combine with an AC 433T diesel engine in it. I took the injector pump off to get it rebuilt and long story short....the drive gear came off the idler gear and we are out of time. We got it to TDC on the 1st cylinder, got the pump lines timed and tried to match the gears up but there is only a mark on the pump's gear and not one on the idler's gear anywhere. So kind of lost as what to do next and wondering if anyone has any ideas. Any help is much appreciated. Thanks.
 
Back to top
View user's profile
Dieseltech
Tractor Guru


Joined: 29 Feb 2012
Posts: 4822
Location: Indiana

Report to Moderator

PostPosted: Tue Nov 14, 2017 9:16 am    Post subject: Re: Allis Chalmers 433T Timing Reply to specific post Reply with quote

Need to find out for sure, I recall that pump should be timed at 18 degrees BTDC on # one compression stroke. If that's where the engine is, then install the pump so the marks under the two screw timing cover are aligned. IGNORE the gear marks, proper crank location and pump in time are all you need. See if the owner's book gives the correct timing #, it may be something other than 18. Some idler gears may or may not be marked. If this is clear as mud, call or text me five seven four eight three five 3292..
 
Back to top
View user's profile
301
New User


Joined: 25 Jun 2015
Posts: 11


Report to Moderator

PostPosted: Wed Nov 15, 2017 9:16 am    Post subject: Re: Allis Chalmers 433T Timing Reply to specific post Reply with quote

If you got the pulley on the right number, pretty sure Diesel tech is right at 18, on compression stroke- lines in the window are on - your good, don't worry about any/ no marks on the drive gears
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters