Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

158 loader part needed---NLA

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
L.C.
Long Time User


Joined: 22 Mar 1998
Posts: 1245


Report to Moderator

PostPosted: Sat Dec 02, 2017 12:25 pm    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

The picture in the parts catalog shows two bends.
Anyone know the angle of the bends and how far
the bends are from the ends of the bar?

If I recall my geometry, it should only be necessary
to measure one angle.
 
Back to top
View user's profile
Hay maker2
Long Time User


Joined: 30 Dec 2013
Posts: 572
Location: Western NY

Report to Moderator

PostPosted: Sat Dec 02, 2017 12:39 pm    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

CVPost-L.C. wrote:
(quoted from post at 21:25:02 12/02/17) The picture in the parts catalog shows two bends.
Anyone know the angle of the bends and how far
the bends are from the ends of the bar?

If I recall my geometry, it should only be necessary
to measure one angle.



the angles are near the end, I will see about getting them tomorrow.
 
Back to top
View user's profile
Scott 730
Long Time User


Joined: 27 Nov 2002
Posts: 826
Location: EC MN

Report to Moderator

PostPosted: Sat Dec 02, 2017 3:58 pm    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

You don't need to figure out the angles. Just measure the offset.
 
Back to top
View user's profile
Scott 730
Long Time User


Joined: 27 Nov 2002
Posts: 826
Location: EC MN

Report to Moderator

PostPosted: Sun Dec 03, 2017 7:02 am    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

CVPost-ArleninOr wrote:
(quoted from post at 20:06:26 12/01/17) Scott, Tim is a lot closer to you than I am. Be cheaper to ship from him. If not let me know.


Arlen, please email me. Thanks.
 
Back to top
View user's profile
Hay maker2
Long Time User


Joined: 30 Dec 2013
Posts: 572
Location: Western NY

Report to Moderator

PostPosted: Sun Dec 03, 2017 9:20 am    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

Scott 730 wrote:
(quoted from post at 00:58:17 12/03/17) You don't need to figure out the angles. Just measure the offset.



There is about 3/4" offset on each end.
The end that mounts on to the frame is bent about 10" from the end. The end the lifts the loader is bent about 6" from the end.
 
Back to top
View user's profile
L.C.
Long Time User


Joined: 22 Mar 1998
Posts: 1245


Report to Moderator

PostPosted: Sun Dec 03, 2017 5:06 pm    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

Thanks for everyone taking the time and effort to
look and take measurements!
 
Back to top
View user's profile
Scott 730
Long Time User


Joined: 27 Nov 2002
Posts: 826
Location: EC MN

Report to Moderator

PostPosted: Tue Dec 05, 2017 7:05 am    Post subject: Re: 158 loader part needed---NLA Reply to specific post Reply with quote

CVPost-ArleninOr wrote:
(quoted from post at 20:06:26 12/01/17) Scott, Tim is a lot closer to you than I am. Be cheaper to ship from him. If not let me know.


Arlen, do you have this part?????????
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters