Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Can't get WC shifter to move between gears???


 
Post new topic    
View previous topic :: View next topic  
Author Message
planebldr
New User


Joined: 07 Dec 2017
Posts: 2


Report to Moderator

PostPosted: Thu Dec 07, 2017 8:45 am    Post subject: Can't get WC shifter to move between gears??? Reply to specific post Reply with quote

So I have a little project that I'm undertaking and have run into a little snag. I have a WC that I can't get to shift between any of the gears. I had another shift tower laying around from one I had for parts and was going to change it out to see if that was it...and the reverse lock was intact on the new shifter. So I remove the old one and check the gears themselves to see if they slide. Yes they do so I don't think it has anything to do with them. I go to install the new tower and line up the forks the the grooves. Finger tighten the bolts and give it a try. Nope...still won't go into any gear. I have a running, driving WC so I know how it should somewhat feel like...and this stays locked in one spot or just 1/2 gear. I tool the tower back out and can't seem to move the shifter at all outside now either. What am I missing?? I feel stupid that I can't figure this out. It seems like it should have been easy Sad Thank you in advance for any help you can give. In the last picture you can almost see that the pin in engaged into the 1/2 gear shift fork lug.
 
Back to top
View user's profile
JoeM(GA)
Long Time User


Joined: 31 Aug 2007
Posts: 1344


Report to Moderator

PostPosted: Thu Dec 07, 2017 10:59 am    Post subject: Re: Can't get WC shifter to move between gears??? Reply to specific post Reply with quote

stuck/rusted detents?
 
Back to top
View user's profile
planebldr
New User


Joined: 07 Dec 2017
Posts: 2


Report to Moderator

PostPosted: Thu Dec 07, 2017 1:21 pm    Post subject: Re: Can't get WC shifter to move between gears??? Reply to specific post Reply with quote

Well, before I got the forks stuck where they are now I could move them back and forth with a definite "click" at the end of the travel. Now it's all bound up lol.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters