Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

remote receptacle won't release


 
Post new topic    
View previous topic :: View next topic  
Author Message
firhead
Regular


Joined: 20 Dec 2012
Posts: 33


Report to Moderator

PostPosted: Wed Dec 06, 2017 3:11 pm    Post subject: remote receptacle won't release Reply to specific post Reply with quote

Got the wood splitter working - thank you all for your input. Now I have a new problem. What I am going to call a receptacle on one of the remotes seems to be stuck in. In other words, the ring with the ball bearings on the inlet side won't come out that 3/8 inch or so the bearings won't spring-load around my hose end. It had not been used for awhile; I can see no way to grab it with anything to pull it out, and I don't know if this would be a solution anyway. Any ideas?
Thanks
Cliff
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 24445


Report to Moderator

PostPosted: Wed Dec 06, 2017 3:25 pm    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote


Barrel on breakaway coupler not moving far enough to rear to release male hyd coupler is a common problem. Take a hammer & tap barrel rearward so that male coupler gets released. There was a post the other day about an aftermarket lever assembly that was marketed to solve this problem.
 
Back to top
View user's profile
41B-boy
Regular


Joined: 28 Aug 2013
Posts: 242
Location: WA

Report to Moderator

PostPosted: Wed Dec 06, 2017 5:37 pm    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

a thought....
my 1070 does that occasionally when the backhoe is mounted. I fought it for hours one day then discovered the pressure relief valve.
grrrrrr.
could that be a solution for you?

Bob
 
Back to top
View user's profile
tim s
Tractor Guru


Joined: 01 Nov 2008
Posts: 11582
Location: Somerset Ohio

Report to Moderator

PostPosted: Wed Dec 06, 2017 5:52 pm    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

They get sticky when not used much,,you can tap the back of it to make it move
 
Back to top
View user's profile
leon
Tractor Expert


Joined: 12 Feb 1998
Posts: 2466


Report to Moderator

PostPosted: Thu Dec 07, 2017 4:27 am    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

Does the 1070 have a pressure relief valve that you can manually momentarily open to make connecting & disconnecting hydraulic lines easier? I wonder if my 855 has that feature? If so, I've never discovered it. Sometimes when I have trouble connecting an implement hose because of too much pressure trapped in it, I put a rag over the end of it's coupler and give it a couple of taps with a hammer. It squirts a little oil and the pressure is relieved and then hooks up easily. But that's on the implement side of things, not the tractor side. For pressure relief on the tractor side, I shut the engine off, move the control lever back & forth to relieve pressure before attempting to hook up.

I too am recently having trouble with the release/lock rings on the tractor's couplers lot locking back. That makes connecting implement couplers more difficult. I'm thinking that the problem my be dust/dirt in that circle of little steel lock/release balls. Next good opportunity I plan on giving that area a good bath with an aerosol can of WD-40 while working the ring back and forth.
 
Back to top
View user's profile
firhead
Regular


Joined: 20 Dec 2012
Posts: 33


Report to Moderator

PostPosted: Thu Dec 07, 2017 10:02 am    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

I thank you all in advance for answers to some pretty simple questions; I'm not real familiar with this stuff. For
starters, on my 2630, how full should I have the hydro fluid? There's no dipstick that I can see and I don't want to
over-fill if this is a possibility. I can bring it all the way up to the filler cap if this is the idea.
Also, I thought that I had the splitter going OK, but might be experiencing what I gather is cavitation: my hoses
are shuddering/vibrating. Now I've had two reasonably credible people tell me it's OK just to tarp strap my remote
lever back to prevent it from kicking back into neutral once I get the splitter in operation. But I keep coming back
to the open center vs closed center thing that I believe TX Jim brought up a few days ago. My valve is a Prince LI
3000-1, which the mfg says cannot be plugged to create a closed-center unit.
Also - and I know folks go all over with this one - can I put something (anything) other than JD hydro fluid in
the tractor? It just seems JD wants top dollar for everything, and I can just see the same fluid coming out of the
same refinery and people putting different price tags on it. Is the stuff you get at Tractor Supply or the local
Mobil/Exxon dealer just as good?

Thanks
Cliff
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 24445


Report to Moderator

PostPosted: Thu Dec 07, 2017 10:53 am    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote


Cliff
Every JD utility tractor I've seen built between '65-'92 had a hyd oil dipstick on RH side of trans case located close to right heel when operator was sitting in seat. Correct method to check hyd oil level on a 2630 is with dipstick nut resting on threads with engine idling & oil at full mark.
 
Back to top
View user's profile
41B-boy
Regular


Joined: 28 Aug 2013
Posts: 242
Location: WA

Report to Moderator

PostPosted: Thu Dec 07, 2017 11:59 am    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

Leon,
Sorry, no. I didn't communicate well that the pressure relief is on the backhoe itself.
It was the general principal I was trying to convey. I honestly don't know if there is a like relief fitting on the tractor. I don't think so.

Sorry for the dirt road...

Bob
 
Back to top
View user's profile
firhead
Regular


Joined: 20 Dec 2012
Posts: 33


Report to Moderator

PostPosted: Thu Dec 07, 2017 3:09 pm    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

It wouldn't be the first time I felt a little, uh.....unobservant.
Thanks
 
Back to top
View user's profile
gene g
Regular


Joined: 12 Nov 2017
Posts: 34


Report to Moderator

PostPosted: Fri Dec 08, 2017 7:54 am    Post subject: Re: remote receptacle won't release Reply to specific post Reply with quote

Shut engine off turn breakaway on , now move scv lever back and forward to relieve oil pressure now turn breakaway off . If you still cannot remove hose reach in front of breakaway and pull or tap receptacle to the rear . If the ball bearings are rusted into the receptacle try pulling on the hose and twisting .
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters