Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Broken Wheel Clamp Studs


 
Post new topic    
View previous topic :: View next topic  
Author Message
albent_33
New User


Joined: 21 Dec 2017
Posts: 2


Report to Moderator

PostPosted: Thu Dec 21, 2017 8:56 am    Post subject: Broken Wheel Clamp Studs Reply to specific post Reply with quote

Hi, I have looked through the other threads and have found no definite answer. I recently picked up a 1941 farmall h with a 3 point hitch not running for $350. While i was taking off the front wheels, I snapped the stud that goes through the hub and wedge that is used to clamp the rim to the hub. The other 2 studs look rusted out near the hub. So my question is, how should I go about fixing this issue? Drill them out? Pound them out? Are they threaded into the hub or just stuck through? There is a square head on the back side of the hub. Thank you for you help!
 
Back to top
View user's profile
glennster
Tractor Guru


Joined: 14 Aug 2007
Posts: 11435
Location: illinois

Report to Moderator

PostPosted: Thu Dec 21, 2017 10:19 am    Post subject: Re: Broken Wheel Clamp Studs Reply to specific post Reply with quote

it is just a square head bolt. you can drive it out. replace it with a grade 5 or 8 hex head bolt.
 
Back to top
View user's profile
albent_33
New User


Joined: 21 Dec 2017
Posts: 2


Report to Moderator

PostPosted: Thu Dec 21, 2017 7:19 pm    Post subject: Re: Broken Wheel Clamp Studs Reply to specific post Reply with quote

CVPost-glennster wrote:
(quoted from post at 11:19:42 12/21/17) it is just a square head bolt. you can drive it out. replace it with a grade 5 or 8 hex head bolt.


I tried that tonight and it still doesn't want to budge. I also applied heat and tried to bang it out. Should I drill it out now?
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 75205
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Thu Dec 21, 2017 7:42 pm    Post subject: Re: Broken Wheel Clamp Studs Reply to specific post Reply with quote

Once rusted in they can be bears to get back out. It may take a lot of ATF soaking and heat and or a press to pop them out
 
Back to top
View user's profile
Bob
Tractor Guru


Joined: 03 Jan 1998
Posts: 49676


Report to Moderator

PostPosted: Thu Dec 21, 2017 8:52 pm    Post subject: Re: Broken Wheel Clamp Studs Reply to specific post Reply with quote

I'd blow 'em out with the smoke wrench in less time than it took you to type your post. Lacking that, and air hammer with a punch tip would probably rattle 'em out.
 
Back to top
View user's profile
RCP
Long Time User


Joined: 24 Feb 2000
Posts: 1210
Location: Western Pa

Report to Moderator

PostPosted: Fri Dec 22, 2017 4:08 am    Post subject: Re: Broken Wheel Clamp Studs Reply to specific post Reply with quote

I was able to find 1/2 x 3 square head bolts on Ebay for our Oliver, if they would work for you, I have extras.

Rich
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Restoration and Repair Tips All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters