Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

F Cub how to remove clutch pivot bushing


 
Post new topic    
View previous topic :: View next topic  
Author Message
Jlpb61
Regular


Joined: 21 Mar 2016
Posts: 57


Report to Moderator

PostPosted: Wed Dec 27, 2017 9:57 am    Post subject: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

Major grinding noise when clutch pushed in. Thanks to ever one I have now split my first tractor. Found couple chunks out of throw out bearing, clutch coming apart and pivot bushing mostly gone. How is the best way to remove what is left of this bushing?
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 76016
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Wed Dec 27, 2017 10:15 am    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

Pivot bushing???????????????????? Do you by chance mean the pilot bearing?? There is a special adaptor made to go on a slide hammer just to pull them. O'Reilly's will rent you one if you do not have one. Since I already had the slide hammer I broke down and bought one not long ago for my slide hammer. Cost me around $17
 
Back to top
View user's profile
Loren in Iowa
Regular


Joined: 14 Mar 1999
Posts: 282


Report to Moderator

PostPosted: Wed Dec 27, 2017 10:33 am    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

If you really are referring to the pilot bushing, in the end of the crankshaft, then I have a trick you might try. Not sure about your specific tractor, but this has worked on car engines. Pump the area inside the bushing full of grease, from a grease gun. Use a shaft, or a socket and extension, as close to the hole diameter, as possible. Drive the shaft into the hole with a hammer, and the grease should push the bushing out.
 
Back to top
View user's profile
john *.?-!.* cub owner
Tractor Expert


Joined: 05 Mar 2009
Posts: 3384


Report to Moderator

PostPosted: Wed Dec 27, 2017 12:05 pm    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

I have removed one by threading a die into it, don't remember the size, but it hit the bottom of hole and pushed the bushing out. There is a website dedicated to the cubs at farmallcub dot com.
 
Back to top
View user's profile
Loren in Iowa
Regular


Joined: 14 Mar 1999
Posts: 282


Report to Moderator

PostPosted: Wed Dec 27, 2017 2:20 pm    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

Quite likely, you threaded a tap into it.
 
Back to top
View user's profile
john *.?-!.* cub owner
Tractor Expert


Joined: 05 Mar 2009
Posts: 3384


Report to Moderator

PostPosted: Wed Dec 27, 2017 7:22 pm    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

CVPost-Loren in Iowa wrote:
(quoted from post at 17:20:02 12/27/17) Quite likely, you threaded a tap into it.
yup, mind went on a brief vacation.
 
Back to top
View user's profile
K-Mo
Regular


Joined: 20 Sep 2014
Posts: 271


Report to Moderator

PostPosted: Thu Dec 28, 2017 3:23 am    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

Haven't used one, but here's an example from Harbor Freight/
Pilot Bearing Puller

 
Back to top
View user's profile
BarnyardEngineering
Tractor Guru


Joined: 23 Mar 2016
Posts: 3633


Report to Moderator

PostPosted: Thu Dec 28, 2017 4:24 am    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

If the bushing is as thin as you say, you should be able to collapse it by catching the edge of it with the corner of a sharp chisel, and tapping on the chisel with a hammer. Then you can grab it with some needle nose vise grips and pull it out.
 
Back to top
View user's profile
Jlpb61
Regular


Joined: 21 Mar 2016
Posts: 57


Report to Moderator

PostPosted: Thu Dec 28, 2017 7:09 am    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote


Everyone
Thanks pilot pivot bearing ( bushing) you can tell i am new at this. But I am enjoying it. Thanks I will let you know how it goes
 
Back to top
View user's profile
Jlpb61
Regular


Joined: 21 Mar 2016
Posts: 57


Report to Moderator

PostPosted: Thu Dec 28, 2017 9:26 am    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

You got this right. I taped a pocket screw driver right under it. Split and came right out.
I am Waiting on my parts now.
Thanks
 
Back to top
View user's profile
roy prins
Long Time User


Joined: 15 Sep 2008
Posts: 861


Report to Moderator

PostPosted: Sun Dec 31, 2017 5:03 pm    Post subject: Re: F Cub how to remove clutch pivot bushing Reply to specific post Reply with quote

fill the bushing with grease - find a shaft that fits the hole somewhat snug and smack it with a hammer-- two or three trys should push it out -- works every time -- Roy
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters