Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Farmall Super C with Woods 306 mower


 
Post new topic    
View previous topic :: View next topic  
Author Message
abengreg
New User


Joined: 31 Aug 2011
Posts: 4


Report to Moderator

PostPosted: Sun Dec 31, 2017 6:28 am    Post subject: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

Recently we purchased a Farmall super c with a woods mower. Noticed the belt was not the best when we got it. Tried it and went about 10 feet and belt came off. Someone rigged up the rear pulleys for the belt with a homemade bracket. I?ve tried 4 different belts from Caseih dealer. All are either too long or too short. I want to replace the pulleys and the bracket in the back with the right ones. Anyone know where I can find these or have them laying around they want to get rid of? Thanks for your help
 
Back to top
View user's profile
rustyfarmall
Tractor Guru


Joined: 07 Feb 2003
Posts: 25064


Report to Moderator

PostPosted: Sun Dec 31, 2017 6:42 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote


You will need to find a Woods dealer. Also, that belt has a specific way to be installed. If it is not correct, it will NOT stay on.
 
Back to top
View user's profile
abengreg
New User


Joined: 31 Aug 2011
Posts: 4


Report to Moderator

PostPosted: Sun Dec 31, 2017 6:54 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

Yes I have the diagram on the mower for the belt routing. I just need
to get the correct bracket and pulleys and then I will get the correct
belt. Just looking for some guidance on what the bracket and pulleys
look like I guess so I can find them.
 
Back to top
View user's profile
leroy in ne
Long Time User


Joined: 02 Sep 2014
Posts: 602


Report to Moderator

PostPosted: Sun Dec 31, 2017 7:06 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

Check woods site, manuals were on line at one time, position of spindle pulleys is important. The one I had to use had problems and I found some one had installed the pulleys even, not staggered as is called for. It would throw the belt and stretch one side or break cords and then you could not keep it on regardless of what you tried. Also correct position of rear idler pulleys is required to be as the book calls for or problems will arise. This is from BTDT. Leroy
 
Back to top
View user's profile
abengreg
New User


Joined: 31 Aug 2011
Posts: 4


Report to Moderator

PostPosted: Sun Dec 31, 2017 7:23 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

Thank you Leroy.
 
Back to top
View user's profile
Farmallhal
Tractor Expert


Joined: 16 Oct 2004
Posts: 2523
Location: Rolla, Missouri

Report to Moderator

PostPosted: Sun Dec 31, 2017 9:13 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

I have a Farmall 140 with a Woods 306L belly mower that I obtained about 10 years or so ago. It was missing some correct or damaged belt drive items and my local Woods dealership was able to obtain new brackets and such directly from Woods which corrected the issues I had with my mower. I believe you can also contact a technical rep at Woods by phone who can probably tell you exactly what items you need and should have on your deck to be compatible with your Super C tractor as well. When I needed a belt I just found the Woods part no. on the old belt and ordered a new one through my Woods dealer. Once you know the Woods part no. for the correct belt for your mower and tractor combination they can also be found aftermarket on eBay if you are looking for a replacement one which is most likely somewhat cheaper if you find one from Woods is too expensive. One thing I did observe with those listed on eBay even though identified as being the correct replacement for my original Woods belt they were sometimes a different length then the actual Woods belt so some caution is advised if purchasing one in that manner, Hal.
 
Back to top
View user's profile
rustyfarmall
Tractor Guru


Joined: 07 Feb 2003
Posts: 25064


Report to Moderator

PostPosted: Sun Dec 31, 2017 11:03 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote


The original belt DOES have a number on it. Takes a bright light and good eyes to see it, and then you may need to rub some white chalk on it. I have a brand new belt for the L306 that is on my H.
 
Back to top
View user's profile
gene bender
Tractor Guru


Joined: 28 Jun 2009
Posts: 10197


Report to Moderator

PostPosted: Sun Dec 31, 2017 11:07 am    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

later mounts for the C series are different they drive from the belt pulley instead of the PTO shaft so which drive do you have. I have the idlers for the later mount which drives from the belt pulley.
 
Back to top
View user's profile
RedRamGT
Regular


Joined: 18 Feb 2017
Posts: 43


Report to Moderator

PostPosted: Sun Dec 31, 2017 1:42 pm    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

Here is a link to Messick's web page for Woods L306U mower parts. If you click on the "Mounting Assembly" it has a parts breakdown for the parts you might need.

http://messicks.com/wo/95317
 
Back to top
View user's profile
Russ from MN
Tractor Guru


Joined: 11 Feb 2006
Posts: 7796
Location: N MN

Report to Moderator

PostPosted: Sun Dec 31, 2017 7:00 pm    Post subject: Re: Farmall Super C with Woods 306 mower Reply to specific post Reply with quote

We have a similar setup on a C, it used a b 225 that I ordered online. I was able to download and print an owners manual online too, it shows every part and how to run the belt. There is a lot of adjustment so belts a little longer or shorter will work too.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters