Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

F12 Sleeve Material


 
Post new topic    
View previous topic :: View next topic  
Author Message
SadFarmall
Long Time User


Joined: 17 Jan 2011
Posts: 888
Location: Bullengarook, Victoria, Australia

Report to Moderator

PostPosted: Tue Jan 09, 2018 2:23 pm    Post subject: F12 Sleeve Material Reply to specific post Reply with quote

Does anyone know whether F12 sleeves are made from steel or cast iron? I was asked earlier this week, but I could not answer!
Thanks,
SadFarmall
 
Back to top
View user's profile
Oldiron29
Tractor Expert


Joined: 22 Oct 2007
Posts: 2091
Location: Suffolk, NY

Report to Moderator

PostPosted: Tue Jan 09, 2018 3:23 pm    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

https://www.youtube.com/watch?v=sUZPByevb8A
Sad, I found this and there seems to be many sites if you Google your question.
 
Back to top
View user's profile
rustred
Tractor Guru


Joined: 01 Jul 2009
Posts: 6756


Report to Moderator

PostPosted: Tue Jan 09, 2018 4:40 pm    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

i am quite sure they were cast as i remember overhauling my w-12.
 
Back to top
View user's profile
teddy52food
Tractor Guru


Joined: 05 Mar 2006
Posts: 8568


Report to Moderator

PostPosted: Tue Jan 09, 2018 7:09 pm    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

All the ones I have worked on were cast iron. Sleeves from an A,B, or c will work if you machine a little off the outside near the bottom.
 
Back to top
View user's profile
SadFarmall
Long Time User


Joined: 17 Jan 2011
Posts: 888
Location: Bullengarook, Victoria, Australia

Report to Moderator

PostPosted: Tue Jan 09, 2018 9:22 pm    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

Thank you! I have looked in my Farmall H Service Training Course, which says sleeves are grey iron. I presume the same goes for F12. Thanks again for the advice. Down to the engineer to get a standard size sleeve made… he wants a project!
SadFarmall
 
Back to top
View user's profile
rustred
Tractor Guru


Joined: 01 Jul 2009
Posts: 6756


Report to Moderator

PostPosted: Wed Jan 10, 2018 6:27 am    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

F12 has wet sleeves, plus once you have them out you can tell what material it is. they have o rings for sealing at bottom. plus machinist would need an old one for sample.
 
Back to top
View user's profile
SadFarmall
Long Time User


Joined: 17 Jan 2011
Posts: 888
Location: Bullengarook, Victoria, Australia

Report to Moderator

PostPosted: Thu Jan 11, 2018 1:38 am    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

I spoke to the local engineer. He will extract the worst sleeve, as we know the correct inside diameter in any case, and work from there… If it all gets too hard, I can go oversize!
SadFarmall
 
Back to top
View user's profile
Dave S.
Long Time User


Joined: 23 Jan 2001
Posts: 878
Location: United States

Report to Moderator

PostPosted: Thu Jan 11, 2018 10:28 am    Post subject: Re: F12 Sleeve Material Reply to specific post Reply with quote

I bought 1 new sleeve from Gordon Rice at Rice Equipment Inc around 3 years ago for my f-12. Just google Rice Equipment Inc,
it should come up and I think there is contact info there.
 
Back to top
View user's profile AIM Address
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters