Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

856


 
Post new topic    
View previous topic :: View next topic  
Author Message
avant 1735
Regular


Joined: 22 Aug 2015
Posts: 162


Report to Moderator

PostPosted: Wed Jan 10, 2018 4:41 pm    Post subject: 856 Reply to specific post Reply with quote

Used my 856 the other day and I heard a clunking sound that appears to be under the tractor, more so on the right side
as you are sitting on it. The next day I used it to more a disk about a 1/2 mile. no noise. I plowed a fence line
about a mile no noise. I used it again today and it made the sound again, about every 6 seconds more or less. I picked
up a round bale and moved it a good way, a couple of times today it did not make any noise for a while, then it would
start again. I am assuming there is a gear with a broken tooth. I have never opened up a rear end of a tractor before,
any suggestions. Thanks
 
Back to top
View user's profile
504
Tractor Guru


Joined: 14 Jun 2005
Posts: 5100


Report to Moderator

PostPosted: Wed Jan 10, 2018 5:19 pm    Post subject: Re: 856 Reply to specific post Reply with quote

Check for loose lug bolts and or loose wheel weights.
 
Back to top
View user's profile
Tom Dowling
Regular


Joined: 29 Oct 2009
Posts: 469


Report to Moderator

PostPosted: Wed Jan 10, 2018 6:06 pm    Post subject: Re: 856 Reply to specific post Reply with quote

what he said
 
Back to top
View user's profile
pete 23
Tractor Guru


Joined: 10 Sep 2009
Posts: 6478


Report to Moderator

PostPosted: Wed Jan 10, 2018 8:14 pm    Post subject: Re: 856 Reply to specific post Reply with quote

Many years ago, customer was complaining about a click in rear of his new tractor. I went out there and tried to duplicate the noise he was hearing. He said it was from the right rear side. I did many donuts in his yard and no noise. Finally, after several questions I was able to figure out he was hearing the hitch reacting while he was plowing using draft control. Told him to just leave that one lever all the way down and end of problem.

Only reason I bring this up is you said you were moving a round bale. If that hitch settles an inch and corrects it's self you will get a pretty good clunk. One chance in a whole lot that this is your problem but just something to keep in mind as you didn't hear it when pulling the implement.

Most likely wheel but don't overlook front wheel also.
 
Back to top
View user's profile
the tractor vet
Tractor Guru


Joined: 24 May 2000
Posts: 14589


Report to Moderator

PostPosted: Thu Jan 11, 2018 8:40 am    Post subject: Re: 856 Reply to specific post Reply with quote

I might add here , does your tractor have the spring loaded park loc????? Twice now on two of our tractors , 1 1066 and my 806 both have the spring loaded park loc.'s and with them they are either all the way off or all the way on and hardly any room for not being all the way off. Due to ware in the linkage they can start clicking to sounding really bad . as there is NO ADJUSTMENT and they give no warning on when they get a little extra ware , the ware can be in the mounting bolt that the park release lever mounts on it could be at either end where the rod goes thru the holes on the lever or at the piviot point going into the range transmission . On my 806 to repair it i had to go find a lever and mounting bolt and buy a new park loc assembly as they do not offer just the rod to get it to stop clicking , really it was more then just a clicking . Make sure your park loc is all the way up and see if this makes and difference .
 
Back to top
View user's profile
Goose
Tractor Guru


Joined: 30 Jun 2007
Posts: 8023


Report to Moderator

PostPosted: Fri Jan 12, 2018 10:39 am    Post subject: Re: 856 Reply to specific post Reply with quote

I agree.

When I started plowing with a semi-mounted plow with an 856 I once had, I kept hearing an intermittent groaning noise in the rear end. I finally figured out it was the draft control working the 3 point arms up and down to keep the plow level.
 
Back to top
View user's profile
Dugger
Long Time User


Joined: 04 Oct 2014
Posts: 552
Location: East central Illinois

Report to Moderator

PostPosted: Mon Jan 15, 2018 4:04 pm    Post subject: Re: 856 Reply to specific post Reply with quote

[quote="CVPost-avant 1735"](reply to post at 19:41:46 01/10/18) [/quote]

Maybe ice in the rearend
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters