Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

G1000 starter wiring


 
Post new topic    
View previous topic :: View next topic  
Author Message
minniemo705
Regular


Joined: 03 Feb 2018
Posts: 54


Report to Moderator

PostPosted: Mon Feb 12, 2018 5:56 pm    Post subject: G1000 starter wiring Reply to specific post Reply with quote

So I'm trying to save myself a bunch of tracing. Have juice at the starter and solenoid and at ignition switch. But the switch doesn't activate the starter. The starter looks exactly the same as my 705 but the solenoids are different. the 705 has the round with 3 terminals but the 1000 has what looks like a solenoid from a ford truck- 4 terminals. Only 3 of those terminals are hooked up. Should all 4 terminals be hooked up? Also what about the neutral start switch- when should it have juice to it? When the key is turned on or when the key is turned to the start position? Also that small solenoid activates that big what I'll call starter gear throw in on top of the starter right? So if that small solenoid is bad it won't activate the starter, but I should still get some clicking or some noise at it, which I'm not, shouldn't I? I get absolutely nothing by turning the key. I just am suspicious of that solenoid not being right. Hoping this is simple- it's to dang cold to for complicated. Thanks
 
Back to top
View user's profile
rvirgil_KS
Long Time User


Joined: 07 Jul 2007
Posts: 1446
Location: Northwest Kansas

Report to Moderator

PostPosted: Mon Feb 12, 2018 6:42 pm    Post subject: Re: G1000 starter wiring Reply to specific post Reply with quote

Did this system work in the past with 4 post solenoid and them fail, or was 4 terminal solenoid added after problems developed.

There are 2 different configurations for the Ford style 4 terminal solenoid. The difference is in the configuration for 2 small posts. The posts may be labeled S and I

Type 1: Solenoid has activating voltage input to S terminal and other end of internal activating coil is grounded through the mount. ?I? terminal receives 12 volt battery voltage when solenoid is activated and sends this 12 volts to the ignition coil to bypass the coil resistor and give a hotter starting spark. Only used on gas or propane engines, not diesel. The ?I? terminal has nothing to do with activating the solenoid.

Type 2: Voltage is applied to S terminal and I goes to ground. Either or both can go through a switch.

Neutral safety switch should be open when gear shift is not in neutral, and closed when shift is in neutral. One side receives voltage when start switch is activated to start position and current should flow through NS switch when gear shift is in neutral. This should activate the S terminal of your first solenoid and turn it on to supply voltage to the switch on the starter.
 
Back to top
View user's profile
minniemo705
Regular


Joined: 03 Feb 2018
Posts: 54


Report to Moderator

PostPosted: Mon Feb 12, 2018 6:57 pm    Post subject: Re: G1000 starter wiring Reply to specific post Reply with quote

It ran but has been sitting 10 plus years- cracked block- and it is diesel. Sounds like neutral switch. I have nothing at those wires no matter what I do with the key switch. So as soon as the key is in start one wire should be sending juice to that switch, but when the key is not being turned to start then there should be no juice at that switch?
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters