Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

John Deere plow bottoms

Goto page 1, 2  Next

 
Post new topic    
View previous topic :: View next topic  
Author Message
SVcummins
Tractor Expert


Joined: 06 Feb 2017
Posts: 2945


Report to Moderator

PostPosted: Mon Feb 12, 2018 9:43 am    Post subject: John Deere plow bottoms Reply to specific post Reply with quote

Can somebody tell me what model bottoms are on this plow




 
Back to top
View user's profile
DeltaRed
Tractor Guru


Joined: 25 Feb 2010
Posts: 14359
Location: Delta,colorado

Report to Moderator

PostPosted: Mon Feb 12, 2018 10:39 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

they look like old 'blacksmith' shares.All I can say is you wont be happy with a JohnDeere plow after pulling an International plow.
 
Back to top
View user's profile
SVcummins
Tractor Expert


Joined: 06 Feb 2017
Posts: 2945


Report to Moderator

PostPosted: Mon Feb 12, 2018 10:42 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

I?ve pulled and owned them both and can?t tell any difference I like the way the John Deere turns the dirt . I was kinda thinking they were blacksmith bottoms as well hopefully Tyler the plow guy will answer
 
Back to top
View user's profile
long green line man
Long Time User


Joined: 03 Feb 2008
Posts: 998


Report to Moderator

PostPosted: Mon Feb 12, 2018 11:32 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Looking at age of plow , I'm thinking NGP334 if 14" /NGP336 if 16".. they were made up to '1968'.. NGP is New General Purpose/ PC 158 on jdparts.com has lots of info..
 
Back to top
View user's profile
long green line man
Long Time User


Joined: 03 Feb 2008
Posts: 998


Report to Moderator

PostPosted: Mon Feb 12, 2018 11:34 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Should be a stamped on part number on back of moldboard....
 
Back to top
View user's profile
tomstractorsandtoys
Tractor Expert


Joined: 30 Nov 2010
Posts: 2355


Report to Moderator

PostPosted: Mon Feb 12, 2018 1:45 pm    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

I agree with you. No other plow turns the dirt over as nice as the Deere. Oliver pulls easier and if you need a reset plow for rocks IH had the best in the 710. Tom
 
Back to top
View user's profile
SVcummins
Tractor Expert


Joined: 06 Feb 2017
Posts: 2945


Report to Moderator

PostPosted: Mon Feb 12, 2018 6:56 pm    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

I like my red plows but I like the John Deere?s to
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 17143
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Mon Feb 12, 2018 8:28 pm    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Blacksmith type, look for the bolt holding them on, The throw away type did not use that large bolt to pull them into place.
 
Back to top
View user's profile
SVcummins
Tractor Expert


Joined: 06 Feb 2017
Posts: 2945


Report to Moderator

PostPosted: Mon Feb 12, 2018 11:15 pm    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Great so I pretty much have a plow I can?t get shares for
 
Back to top
View user's profile
Briar Hill Brittanys
Long Time User


Joined: 14 May 2009
Posts: 1076
Location: Jasper, MO

Report to Moderator

PostPosted: Tue Feb 13, 2018 4:10 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Give Tyler the plow guy a holler, I believe he'll be able to help you.http://www.mrbtractors.com/plow_parts
 
Back to top
View user's profile
DR. EVIL
Long Time User


Joined: 26 Aug 2014
Posts: 1067


Report to Moderator

PostPosted: Tue Feb 13, 2018 4:57 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Dad bought the matching Deere 4-14 plow to pull with his JD R diesel spring of 1964. Dad hated running the tractor, said it was MY tractor, and it sat until I could run it on weekends and he would run his Super M-TA. Only pulled the Deere plow on 40 acres of alfalfa sod. Got tired of crawling around the field in 2nd gear, had one hill I had to drop into low gear on. Rest of the plowing I pulled a 3-14 IH #8, could run in 3rd gear then. Still had 16 acres of plowing left when the R left the farm, pulled the Deere plow with the SM-TA on that. Deere plow disappeared shortly after we were done plowing.

Really disliked the IH #8 plows, Dad had two. No trash clearance. Neighbor had good things to say about Case plows, Dad bought a 4-14 Case pull plow to use with a Midwest plow harrow behind a 450 Farmall. Plugging when plowing old corn ground almost stopped completely. Couple years later the Case 4-14 was traded for a Case 5-14 and the plow harrow widened accordingly to use behind the 4010-D. Plowed 30 acres and the back bottom was pulled off the plow, was back in 2nd gear in corn ground again. That plow sold as a 4-14 with a spare bottom and coulter.

The newer IH pull plows, #60 & #70 would be my first choice but I'd have no problem buying or using a good Case plow. I have NO desire to plow with a #8 plow again, I've wasted enough time in my life digging corn stalks out of them.
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 17143
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Tue Feb 13, 2018 6:55 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

You can get new shares but they are expencige. Forget Tyler he is just a reseller, nothing against him. But go straight to the factory and that is Steve Rea at Ploworx. Just had his information in my hand yesterday don't know where I laid it off hand. He bought out the old cresent forge. Just go back thru this section and you will find dozens of reference to him. He is in Ohio. I think there is 2 or 3 referals to hin on here since new years day. If you use it you will have to learn how to sharpen the shares with heat that I can help with.
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 17143
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Tue Feb 13, 2018 7:01 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Steve Smith of Republic, Ohio is known as the Plow peddler and he may have new or good used shares. silco@bright.net 419-618-0017 Last fall I sold him a bunch of plow parts I no longer had use for Including JD shares. Nice guy.
 
Back to top
View user's profile
Leroy
Tractor Guru


Joined: 09 Jan 1998
Posts: 17143
Location: Wapakoneta, Ohio

Report to Moderator

PostPosted: Tue Feb 13, 2018 7:26 am    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

As of now just go back 3 pages on Jan 29 and you will find Ploworx information. Steve rea, 13909 Duck Creek Rd., Salem, Ohio 44460 330-332-9386 ploworx@att.net web www.ploworx.com Still have leters on my computor from when he first started, seens nice. And on those shares that big bolt you see hooks onto a hook on back side of share and that is what holds the share on. A 3/8" bolt with a small casting on that bolt goes into a notch on the frog and if the big bolt comes loose that small one will keep share from falling off. And I know Steve Smith has those pieces as that is some of what I sold him last November.
 
Back to top
View user's profile
SVcummins
Tractor Expert


Joined: 06 Feb 2017
Posts: 2945


Report to Moderator

PostPosted: Tue Feb 13, 2018 1:44 pm    Post subject: Re: John Deere plow bottoms Reply to specific post Reply with quote

Thanks Leroy .
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters