Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Ford 8n trans-mix axle bracket


 
Post new topic    
View previous topic :: View next topic  
Author Message
rtj1972
New User


Joined: 23 Sep 2015
Posts: 6


Report to Moderator

PostPosted: Mon Apr 16, 2018 7:30 am    Post subject: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

I need to build the axle brackets for a trans-mix cement mixer to fit a 8n and I
need the dimension and hole spacing. I was hoping that someone could help me.
 
Back to top
View user's profile
HCooke
Tractor Guru


Joined: 29 Sep 2006
Posts: 5332
Location: Missouri

Report to Moderator

PostPosted: Mon Apr 16, 2018 1:59 pm    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

Might try the other forum. Someone there, maybe Jim(Utah) used to have one.
 
Back to top
View user's profile
Nebraska Cowboy
Regular


Joined: 02 Nov 2009
Posts: 150
Location: Columbus, NE

Report to Moderator

PostPosted: Mon Apr 16, 2018 2:16 pm    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

CVPost-rtj1972 wrote:
(quoted from post at 16:30:52 04/16/1Cool I need to build the axle brackets for a trans-mix cement mixer to fit a 8n and I
need the dimension and hole spacing. I was hoping that someone could help me.


What can I help you with? I own one and would be glad to help you out. Not at my shop now however, will be tomorrow morning.
 
Back to top
View user's profile
rtj1972
New User


Joined: 23 Sep 2015
Posts: 6


Report to Moderator

PostPosted: Mon Apr 16, 2018 6:02 pm    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

I need the measurements of the hole
locations and the overall size of the
bracket


 
Back to top
View user's profile
Tim PloughNman Daley
Tractor Expert


Joined: 18 Sep 2004
Posts: 2156


Report to Moderator

PostPosted: Tue Apr 17, 2018 1:41 am    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

There are three documents on the NTC site, under MANUALS/MISC, including the original owner/operator/setup manual. Jim(UT) has been absent for a few years now as he has gotten out of the tractor business so he doesn't post there anymore. The documents are in pdf and you can download them for free. There is a fella about 55 miles from me who has a 9N with a Trans-Mix mounted. It is parked outside his HD construction business. I once left a note on it asking if he wanted to sell just the mixer and he called me and said no, he still uses it. If you get stumped, I could stop and measure it but no plans to get that way anytime soon. My email is open if you want to save it in case...

Tim *PloughNman* Daley(MI)
 
Back to top
View user's profile
Bob
Tractor Guru


Joined: 03 Jan 1998
Posts: 50373


Report to Moderator

PostPosted: Tue Apr 17, 2018 4:40 am    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

Knowing what the distance is between the fender bolt holes you should be able to "scale" the parts in the photos and get awful darned close.
 
Back to top
View user's profile
Hobo,NC
Tractor Guru


Joined: 14 Jun 2007
Posts: 17161
Location: Sanford,NC

Report to Moderator

PostPosted: Tue Apr 17, 2018 8:23 am    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote


Bolt hole center 4.825
 
Back to top
View user's profile
rtj1972
New User


Joined: 23 Sep 2015
Posts: 6


Report to Moderator

PostPosted: Tue Apr 17, 2018 9:10 am    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

I want to thank all of you for your help, I think I have the built.
 
Back to top
View user's profile
Nebraska Cowboy
Regular


Joined: 02 Nov 2009
Posts: 150
Location: Columbus, NE

Report to Moderator

PostPosted: Tue Apr 17, 2018 12:13 pm    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

Angle iron bracket is 14 inches long and is 2 & 1/2 inches by 2 & 1/2 inches by 1/4 inch thick. 1 side has a 2 inch notch cut out of it and has the one hole that is 1 inch center from the end




 
Back to top
View user's profile
Tall T
Tractor Expert


Joined: 26 May 2014
Posts: 3218
Location: Salt Spring Island

Report to Moderator

PostPosted: Tue Apr 17, 2018 8:55 pm    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

Looks like 1.25" to the center of the hole all right. Smile
 
Back to top
View user's profile
rtj1972
New User


Joined: 23 Sep 2015
Posts: 6


Report to Moderator

PostPosted: Wed Apr 18, 2018 3:46 am    Post subject: Re: Ford 8n trans-mix axle bracket Reply to specific post Reply with quote

Thank you, just what I needed.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford 9N, 2N, 8N All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters