Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

how do i make lowtension start hotshot?


 
Post new topic    
View previous topic :: View next topic  
Author Message
derwen1959
Long Time User


Joined: 27 Feb 2016
Posts: 631


Report to Moderator

PostPosted: Sat Apr 21, 2018 7:37 am    Post subject: how do i make lowtension start hotshot? Reply to specific post Reply with quote

Ivor here from UK and I have been lucky enough to find an Amanco 2 3/4 open crank which has never been converted to high tension and I remember reading somewhere that the low tension can be by passed using a 6volt torch battery for starting but is it straight forward to do? I should add that I have yet to fetch engine
 
Back to top
View user's profile
Butch(OH)
Tractor Expert


Joined: 19 Jun 2000
Posts: 3157


Report to Moderator

PostPosted: Fri May 04, 2018 2:40 am    Post subject: Re: how do i make lowtension start hotshot? Reply to specific post Reply with quote

I assume it has a magneto on it presently? If so you need to disconnected it from the igniter to prevent damage prior to using a battery. You will need some sort of a coil, regular low tension coils can be had for $50-70. You may also use the primary windings on a high tension coil for this or I have seen the pull in winding for a starter solenoid used. Or you can make your own, search "homemade low tension coil" If you use a make-do or homemade coil the test to see if it will run the engine is to connect a ground, or earth I think you say over there? from the battery to the coil and then attach a wire to the other terminal and quickly touch it to the + battery post. A good coil will yield a nice hot spark when the wire is removed. A weak coil can be temporarily boosted with a 12V battery to start the engine but the set up will be hard on the points if run for long periods. Once you have assured that your coil has the ability to make a good spark the engine wiring is simple. Connect the - side of the battery to the engine block. Then run a wire from the + terminal to the one of the coil terminals. From the other coil terminal you go to the ignitor. Before you wear yourself out cranking you can test the ignitor for function by these tests. A- with the points open and everything wired up you should be able to remove either wire, ground or hot and touch it back and remove it without getting a spark. B-if that passes then close the igniter points and try again, and you shouldget a good spark when you remove the wire. Good luck with it.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Stationary Engines All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters