Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Tea20 choke plate operation zenith 24T-2


 
Post new topic    
View previous topic :: View next topic  
Author Message
kaesark
Regular


Joined: 15 Nov 2016
Posts: 217


Report to Moderator

PostPosted: Sat Jun 09, 2018 7:59 pm    Post subject: Tea20 choke plate operation zenith 24T-2 Reply to specific post Reply with quote

Think my choke Plate is either sticking or the choke spindle spring is faulty. When I pull back on the choke lever the choke plate stays open however if I give the choke spring anchor plate a slight twist then the choke plate springs shut. Can the tension on the choke spindle spring be adjusted or is a replacement needed.
Thanks

 
Back to top
View user's profile
John Deere D
Tractor Expert


Joined: 14 Jun 2011
Posts: 2648


Report to Moderator

PostPosted: Sat Jun 09, 2018 11:15 pm    Post subject: Re: Tea20 choke plate operation zenith 24T-2 Reply to specific post Reply with quote

Tomorrow, I shall check the carb on my daily user TEA-20:

Bob..

 
Back to top
View user's profile
kaesark
Regular


Joined: 15 Nov 2016
Posts: 217


Report to Moderator

PostPosted: Sat Jun 09, 2018 11:34 pm    Post subject: Re: Tea20 choke plate operation zenith 24T-2 Reply to specific post Reply with quote

Appreciate your help as I am not clear on just what or how the choke plate should work. I was thinking that pulling back the choke lever would allow the spindle spring to do it's thing and close the choke plate.
Thanks
 
Back to top
View user's profile
kaesark
Regular


Joined: 15 Nov 2016
Posts: 217


Report to Moderator

PostPosted: Mon Jun 11, 2018 12:59 am    Post subject: Re: Tea20 choke plate operation zenith 24T-2 Reply to specific post Reply with quote

I have given everything a good soak in oil to see if I could free up choke plate movement. Put a torch down choke barrel and I think choke plate is rubbing on one side of barrel. If I loosened plate screws will I get desired movement of plate that is sideways so as to centralise on spindle so as to eliminate rubbing on side of barrel.
 
Back to top
View user's profile
John Deere D
Tractor Expert


Joined: 14 Jun 2011
Posts: 2648


Report to Moderator

PostPosted: Mon Jun 11, 2018 4:31 pm    Post subject: Re: Tea20 choke plate operation zenith 24T-2 Reply to specific post Reply with quote

Quote:

If I loosened plate screws will I get desired movement of plate that is sideways so as to centralise on spindle so as to eliminate rubbing on side of barrel.

YES....
That is exactly as per my picture and instructions:

loosen Plate screws, close choke plate ...and then tighten Plate Screws....Choke plate shall now be centered in bore of Carb.

All dirt and grime must be removed from around rotating shafts:

Bob...



 
Back to top
View user's profile
kaesark
Regular


Joined: 15 Nov 2016
Posts: 217


Report to Moderator

PostPosted: Wed Jun 13, 2018 3:10 am    Post subject: Re: Tea20 choke plate operation zenith 24T-2 Reply to specific post Reply with quote

All fixed with no thanks to the previous owner who had put spring washer on wrong side of spring.
Thanks
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Harry Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters