Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Oliver plow

Goto page Previous  1, 2

 
Post new topic    
View previous topic :: View next topic  
Author Message
OliverNate
Long Time User


Joined: 16 Apr 2012
Posts: 543


Report to Moderator

PostPosted: Wed Jun 20, 2018 5:27 pm    Post subject: Re: Oliver plow Reply to specific post Reply with quote

Whatever you got thats skinny and tall. If they are 16in rims on there I'd look for like a 225/75R16 those are probly a bit too wide but that's probly the
closest you'll get in a radial. Unless you change rims but then you'll need fine thread bolts and lug nuts from a car to fit bolts because those rims have a
square hole for the lug holes and are held on by carriage bolts.
 
Back to top
View user's profile
sowhatofit
Regular


Joined: 09 May 2018
Posts: 28


Report to Moderator

PostPosted: Wed Jun 20, 2018 6:03 pm    Post subject: Re: Oliver plow Reply to specific post Reply with quote

Ok,thanks. Looks like some of the carriage bolts are semi new, so shouldn't be too hard to get them off.

Also wondering if this implement will hill beyond the tire. I suppose that depends on speed? I'm row planting and may need to hill up on the plants. Never had a plow before. Just a disc and a cultivator/tine tiller.
 
Back to top
View user's profile
OliverNate
Long Time User


Joined: 16 Apr 2012
Posts: 543


Report to Moderator

PostPosted: Thu Jun 21, 2018 8:25 pm    Post subject: Re: Oliver plow Reply to specific post Reply with quote

The front bottom will take the soil and flip it upside down directly behind the tire. You could do some experimenting but I doubt its going to do what you want
it to. If you have light and loose soil it might work but you going to need the furrow tire as close as possible to the plant. Also they tend to not turn ground
the best when the furrow wheel is not in a furrow. Typically when you plow the first pass you gotta set it deep so the front board gets in the ground. This is
also when they are the worst for plugging because those old plows have no trash clearance. For what you want to do I'd be on the look out for a row cultivator
with disc hillers on it.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters