Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Re: Massey Ferguson 135


 
Post new topic    
View previous topic :: View next topic  
Author Message
DavidP, South Wales
Tractor Expert


Joined: 29 Jun 2010
Posts: 2211


Report to Moderator

PostPosted: Sat Jun 16, 2018 6:38 am    Post subject: Re: Massey Ferguson 135 Reply to specific post Reply with quote

Hi, standard brakes on 135 and 165 not the
same. 14x2 shoes on 135 and dry or wet
discs on 165. 165 normally needs special
puller to remove epicyclic reduction unit
from hub in order to remove shaft and then
the seal from the outer housing.
DavidP, South Wales.
 
Back to top
View user's profile
Robg165
New User


Joined: 19 Jul 2017
Posts: 3


Report to Moderator

PostPosted: Sat Jun 16, 2018 2:11 pm    Post subject: Re: Massey Ferguson 135 Reply to specific post Reply with quote

Thanks for your response. I have the axle disassembled. My problem is how to remove the seal from the outer end of the axle. The metal part of the seal is pressed into the housing and as a result there is nothing to pry or grab on to from the outside. Any suggestions you have would be appreciated.

 
Back to top
View user's profile
DavidP, South Wales
Tractor Expert


Joined: 29 Jun 2010
Posts: 2211


Report to Moderator

PostPosted: Sun Jun 17, 2018 10:13 am    Post subject: Re: Massey Ferguson 135 Reply to specific post Reply with quote

Hello,
using a small round punch or chisel and hammer you should be able to close the top (in photo) edge of the seal in. Tap around until it is all closed in and using a grips you should be able to lift the seal out.

DavidP
 
Back to top
View user's profile
Robg165
New User


Joined: 19 Jul 2017
Posts: 3


Report to Moderator

PostPosted: Thu Jun 21, 2018 9:54 am    Post subject: Re: Massey Ferguson 135 Reply to specific post Reply with quote

David, thanks for taking the time to offer your advice. Novices like me really do appreciate it when those more experienced like you offer your wisdom. It makes it so much easier for us. I ended up using a slide hammer puller to remove the outer axle seal and am in the process of putting the tractor back together. I feel as if the hard part is done.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Massey Harris & Massey Ferguson All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters