Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Farmall 300 rear hydrualic lines


 
Post new topic    
View previous topic :: View next topic  
Author Message
330 Standard
Regular


Joined: 29 Nov 2011
Posts: 43


Report to Moderator

PostPosted: Tue Oct 09, 2018 10:59 am    Post subject: Farmall 300 rear hydrualic lines Reply to specific post Reply with quote

Anybody know of anyone who sells or repairs farmall hydraulic lines. I have a 300 that had a pinhole rust thru on the lines going to the rear fast hitch cylinder. I got it off and we welded up the worst pitted places but given as much trouble as it was to remove from under the dash I'd like to buy a new set or have the blocks re-tubed so I don't have to go thru pulling it off again in the future when another pitted place blows out. Thanks
 
Back to top
View user's profile
fastfarmall
Tractor Expert


Joined: 05 Feb 2015
Posts: 3227


Report to Moderator

PostPosted: Tue Oct 09, 2018 11:52 am    Post subject: Re: Farmall 300 rear hydrualic lines Reply to specific post Reply with quote

So was that sitting with he valve cover off, that's what it looks like to me,I bought a tap and die set that was in the original plastic blow formed container, a little water got in there i had to use the[1/3 horse] wire brush on each piece to get the rust off!
 
Back to top
View user's profile
2late4me
Regular


Joined: 02 Dec 2017
Posts: 43


Report to Moderator

PostPosted: Wed Oct 10, 2018 5:45 am    Post subject: Re: Farmall 300 rear hydrualic lines Reply to specific post Reply with quote

I know it's not approved by the correct police but the tube is usually still good on the vertical part so I will cut the line and use a nut and ferule and run a hose to the rear.
 
Back to top
View user's profile
charlieu
Long Time User


Joined: 23 Dec 2011
Posts: 526
Location: Southern MN

Report to Moderator

PostPosted: Wed Oct 10, 2018 3:43 pm    Post subject: Re: Farmall 300 rear hydrualic lines Reply to specific post Reply with quote

A number of years ago I needed the lower tube for my 350 Farmall, I went to a Hyd tube bender and had some made up. If the tube you need is the lower one. I can sell you what you need. The old tube can be heated for removal and the replacement is silver soldered in. Charlie U
 
Back to top
View user's profile Visit poster's website
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters