Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

300U crank pully


 
Post new topic    
View previous topic :: View next topic  
Author Message
Iam2
New User


Joined: 05 Apr 2018
Posts: 13
Location: Eastern Colorado

Report to Moderator

PostPosted: Tue Oct 09, 2018 2:27 pm    Post subject: 300U crank pully Reply to specific post Reply with quote

Hello: we have a 300U partially tore down looking for boogered cam keyway and just noticed the crank pully is not the stock pully and it has extra timing marks like a total of four, does anyone have a stock one to check before I tear further? the timing seems to be off as it wont run good anywhere its set. this one was part of a Wagner front end loader kit and im thinking it was made to fit more than farmalls with extra marks?
 
Back to top
View user's profile
sunsettractor
Regular


Joined: 18 Mar 2009
Posts: 189


Report to Moderator

PostPosted: Tue Oct 09, 2018 4:38 pm    Post subject: Re: 300U crank pully Reply to specific post Reply with quote

Here is a scan of pulley in 300U operators manual, the pulley has 4 marks it.

 
Back to top
View user's profile
mattofvinings
Long Time User


Joined: 05 Mar 2009
Posts: 605
Location: Saline, MI

Report to Moderator

PostPosted: Wed Oct 10, 2018 12:24 am    Post subject: Re: 300U crank pully Reply to specific post Reply with quote

I would verify, by pulling out #1 plug and shining an LED flashlight into the port, that when turning the engine by hand, you can see the piston crown hit the apex of its stroke, and at that point, that the timing marks are somewhat close to the stationary indicator. If that test fails then the crank pulley is not correctly set.

Before you set distributor timing there, its advisable to pull the rocker cover and look at both the intake and exhaust valves. There are two times that TDC is reached in the combustion cycle spanning 2 revs of the crank. Only one of these is proper to set the ignition timing. The #1 cyl intake and exhaust valves will be "quiet" on both sides of the "correct TDC", as opposed to movement observed right around the "incorrect TDC".
 
Back to top
View user's profile
Iam2
New User


Joined: 05 Apr 2018
Posts: 13
Location: Eastern Colorado

Report to Moderator

PostPosted: Wed Oct 10, 2018 7:50 pm    Post subject: Re: 300U crank pully Reply to specific post Reply with quote

Thanks! You tripped my brain and I borrowed 2 old owners manuals with a wealth of information in them. They go into setting the time in detail and also maintance of the timing advancing system, I have to slow the rpm's down to below 375 as above that it start advancing which will give a wrong/false setting then proceed to set the timing .
Next I have to take the power steering off and see where its leaking from and fix that! Thanks for the help finding the right manuals!
 
Back to top
View user's profile
sunsettractor
Regular


Joined: 18 Mar 2009
Posts: 189


Report to Moderator

PostPosted: Wed Oct 10, 2018 9:27 pm    Post subject: Re: 300U crank pully Reply to specific post Reply with quote

Fantastic! Looking forward to hearing good news about your project.
Please keep us posted...Tom
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Farmall & International Harvester (IHC) All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters