Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Pto v belt pulley

Goto page 1, 2  Next

 
Post new topic    
View previous topic :: View next topic  
Author Message
Graveyard1984
Regular


Joined: 02 Nov 2017
Posts: 115


Report to Moderator

PostPosted: Thu Oct 11, 2018 8:02 pm    Post subject: Pto v belt pulley Reply to specific post Reply with quote

Do they make a v belt pulley that will work on a rear pto shaft? If so where can i find one?

How many rpms will the pto spin at full throttle on a m farmall?
 
Back to top
View user's profile
Andy Martin
Tractor Guru


Joined: 03 Sep 2000
Posts: 4689


Report to Moderator

PostPosted: Thu Oct 11, 2018 8:22 pm    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

You could easily make one with a weld-on pulley and machine a PTO adapter to fit.

An M will turn over 540 RPM on the PTO. You'll find belt power is limited at low speeds, you may want twin drives. I've used a chain and a couple of sprockets to get the speed up before going to a v-belt.
 
Back to top
View user's profile
gene bender
Tractor Guru


Joined: 28 Jun 2009
Posts: 10187


Report to Moderator

PostPosted: Fri Oct 12, 2018 12:12 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

Just find a Browning dealer. They will have the hub with the splines to fit the PTO and the pulley to fit that hub
 
Back to top
View user's profile
BAnNC
Tractor Guru


Joined: 15 Oct 2012
Posts: 4746


Report to Moderator

PostPosted: Fri Oct 12, 2018 2:14 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

Had one on a Ford 641 that was for a side cycle. Had twins on it. Just as OP said here, pto connector with twin v belt pulleys on it. That was a Ford product.
 
Back to top
View user's profile
Geo-TH,In
Tractor Guru


Joined: 05 Aug 2009
Posts: 16332
Location: terre haute

Report to Moderator

PostPosted: Fri Oct 12, 2018 3:06 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

I have a large pulley on my Farmall C's pto. It about 16-18 inches in diameter. It powers a woods 6 ft belly mower. I put an want ad on TY and bought the 6 ft woods mower that was used on Farmall H & M.
As others said 540 rpms.
 
Back to top
View user's profile
Mike M
Tractor Guru


Joined: 31 Mar 1998
Posts: 26362


Report to Moderator

PostPosted: Fri Oct 12, 2018 4:19 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

I remember seeing at one of the farm stores the weld a pulley rack and they offered a hub made to go on a pto shaft. Buy the hub and buy the pulley and you weld them together.
 
Back to top
View user's profile
TJV
Regular


Joined: 16 Mar 2012
Posts: 425
Location: MN

Report to Moderator

PostPosted: Fri Oct 12, 2018 5:12 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

I have a Browning hub here for the taper lock type pulley or sprocket the numbers stamped on it are P2 1 3/8-6 SPL B I also have a weld a hub type one on another tractor so you have options

 
Back to top
View user's profile
Russ from MN
Tractor Guru


Joined: 11 Feb 2006
Posts: 7781
Location: N MN

Report to Moderator

PostPosted: Fri Oct 12, 2018 5:16 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

You definitely want a taper-lock, it's the only way to get it tight.
 
Back to top
View user's profile
IA Roy
Tractor Expert


Joined: 22 Mar 2005
Posts: 1704


Report to Moderator

PostPosted: Fri Oct 12, 2018 5:36 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

They will turn 540 or a little more. The surface speed of the belt is all dependent on the diameter. Like others say the belly mowers use a large pulley to get belt speed up and the larger they are the more power they can transmit
 
Back to top
View user's profile
John730D
Tractor Expert


Joined: 02 Jan 2008
Posts: 1869


Report to Moderator

PostPosted: Fri Oct 12, 2018 5:44 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

I have a taper lock 20 inch double grove pully I would sell cheap. The taper lock hub is for a 540 PTO shaft. Let me know if you need it. Email should be open.
 
Back to top
View user's profile
DoubleO7
Tractor Expert


Joined: 27 Oct 2017
Posts: 1674
Location: Crystal River, FL

Report to Moderator

PostPosted: Fri Oct 12, 2018 7:13 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

Get the taper lock hub for the pto shaft.
Then get the pulley you think you need to go with the hub.

That way if you need or want to change to a different size pulley or put a chain sprocket on it you can.

If you do the weld-a-hub to sprocket, your stuck with that assembly and have to create an entire new assembly in order togo with a different pulley or sprocket.
 
Back to top
View user's profile
rustyfarmall
Tractor Guru


Joined: 07 Feb 2003
Posts: 25048


Report to Moderator

PostPosted: Fri Oct 12, 2018 7:30 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote


My Woods belly mower is belt driven from a pulley mounted on the PTO shaft.
 
Back to top
View user's profile
IA Roy
Tractor Expert


Joined: 22 Mar 2005
Posts: 1704


Report to Moderator

PostPosted: Fri Oct 12, 2018 9:57 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

Motion Industries is a Browning dealer. Lots of stores. It is a big chain for power train components.
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 78241
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Fri Oct 12, 2018 10:03 am    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

Most any good farm and home store will have blank PTO has and pulleys that one can weld onto the hub. I have welded up a good many of them over the years
 
Back to top
View user's profile
Graveyard1984
Regular


Joined: 02 Nov 2017
Posts: 115


Report to Moderator

PostPosted: Fri Oct 12, 2018 7:21 pm    Post subject: Re: Pto v belt pulley Reply to specific post Reply with quote

The pulley just bolts to that piece in the picture?
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Talk All times are GMT - 8 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters