Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Marvel Schebler TSX 695 carb.


 
Post new topic    
View previous topic :: View next topic  
Author Message
Ernie Polley
New User


Joined: 21 Oct 2007
Posts: 1


Report to Moderator

PostPosted: Sun Oct 21, 2007 7:38 pm    Post subject: Marvel Schebler TSX 695 carb. Reply to specific post Reply with quote

Does anyone out there have an exploded view of an MS TSX 695 carb. It"s on a MF 65 4 cyl G-176 Continental gas motor. I have a diagram for a MS TSX 616 carb. Are they the same ???
 
Back to top
View user's profile
old
Tractor Guru


Joined: 12 Mar 2000
Posts: 56971
Location: Lake of the Ozarks area of MO

Report to Moderator

PostPosted: Sun Oct 21, 2007 8:47 pm    Post subject: Re: Marvel Schebler TSX 695 carb. Reply to specific post Reply with quote

There so close that you will never be able to figure out what is different between to 2 of them. Things like jet size maybe different but thats about it
Hobby farm

 
Back to top
View user's profile
dobber
Guest






Report to Moderator

PostPosted: Mon Oct 22, 2007 5:10 am    Post subject: Re: Marvel Schebler TSX 695 carb. Reply to specific post Reply with quote

I'm not sure what the TSX-616 fit but your MF 65 did originally use the TSX-695. They had different numbers for different applications because throttle or choke linkage could be on different sides or lever part different. Measure the throttle bore size as the TSX was made with 7/8", 1", & 1 1/4" bore sizes and each of those used about 5 to 8 different sizes of venturis in center also. So they may all look a bit the same on outside but aren't the same using different numbers for a reason. May VE Petersen in Ohio can tell you 800-537-6212 or zenithfuelsystems.com Basic construction and float setting should be the same.
 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tractor Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters