Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

UB engine


 
Post new topic    
View previous topic :: View next topic  
Author Message
LBSMJS
Guest






Report to Moderator

PostPosted: Wed Mar 13, 2013 8:47 pm    Post subject: UB engine Reply to specific post Reply with quote

Was thinking about putting a 403 crankshaft & rods in my UB.How large of piston could I bore the jugs for,& does anyone make a piston that would go on those rods and work in the 283 jugs.Thanks.
 
Back to top
mmdiesel
Regular


Joined: 11 Dec 2012
Posts: 46


Report to Moderator

PostPosted: Thu Mar 14, 2013 9:23 am    Post subject: Re: UB engine Reply to specific post Reply with quote

I have a set of UB diesel jugs that are sleeved to 5.125". The jugs won't fit in the crankcase without grinding the crankcase. There are custom made jugs that run close to 6" pistons.
 
Back to top
View user's profile
LBSMJS
Guest






Report to Moderator

PostPosted: Thu Mar 14, 2013 3:56 pm    Post subject: Re: UB engine Reply to specific post Reply with quote

Is there a piston available that would fit them and work with the 403 crank & rods.
 
Back to top
LBSMJS
Guest






Report to Moderator

PostPosted: Sat Mar 16, 2013 7:49 am    Post subject: Re: UB engine Reply to specific post Reply with quote

I might be interested in those jugs. How do i contact you.
 
Back to top
mmdiesel
Regular


Joined: 11 Dec 2012
Posts: 46


Report to Moderator

PostPosted: Wed Mar 20, 2013 8:04 am    Post subject: Re: UB engine Reply to specific post Reply with quote

My email is lised below:

Michael Moeller
mmdieselpuller@yahoo.com
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters