Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

MM Baler Help Needed


 
Post new topic    
View previous topic :: View next topic  
Author Message
Jim Calhoun
Guest






Report to Moderator

PostPosted: Sat Apr 13, 2013 7:51 pm    Post subject: MM Baler Help Needed Reply to specific post Reply with quote

I have an old MM twine tie baler fro the 1950's. It is a model 760.
It is missing the knives for the knotters. It seems to be the type that McCormick used in the 50's and does not have the arm that pushes the knot off the bill hook. It simply uses the backward motion and weight of the bale to do that job. ANY information as to where to get knives for this baler would be greatly appreiated!
 
Back to top
JK2
Regular


Joined: 19 Aug 2004
Posts: 397


Report to Moderator

PostPosted: Sun Apr 14, 2013 4:45 am    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

Supposedly those knotters were all replaced by a New Holland knotter by the dealers because they had so many problems with them. Those knotters were later raised up higher so the end of the stems from being cut on top of the bale didn"t interfere with the knot being made. I think I have a whole New Holland knotter assembly that I saved from a baler being junked. I"m pretty sure I don"t have any parts for the international style knotters. If I remember correctly, some of the parts from a 45 Int baler will fit.
John
 
Back to top
View user's profile
Jim Calhoun
Guest






Report to Moderator

PostPosted: Sun Apr 14, 2013 7:13 am    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

How can I contact you about the New Holland Knotters? I am wery interested!
 
Back to top
JK2
Regular


Joined: 19 Aug 2004
Posts: 397


Report to Moderator

PostPosted: Sun Apr 14, 2013 9:03 am    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

My e-mail is open. Send me a picture of yours (or post it) so I can look to see what all you need to make sure I have it all.
 
Back to top
View user's profile
Jim Calhoun
Guest






Report to Moderator

PostPosted: Mon Apr 15, 2013 7:31 am    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

I will send pictures asap
Thanks for your help!
 
Back to top
Tractor_Guy
Regular


Joined: 01 Apr 2010
Posts: 90


Report to Moderator

PostPosted: Mon Apr 15, 2013 7:20 pm    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

I have a set of IH 45 knotters if you need parts from them

Joe
 
Back to top
View user's profile
Jim Calhoun
Guest






Report to Moderator

PostPosted: Mon Apr 15, 2013 10:03 pm    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

I would be interested in the knotters you have. I am not real good at figuring out how to communicate well on the forum so please email me at : jimcalhounmusic@gmail.com and we will see what we can come up with.
Thanks
 
Back to top
Jim Calhoun
Guest






Report to Moderator

PostPosted: Wed May 01, 2013 8:49 pm    Post subject: Re: MM Baler Help Needed Reply to specific post Reply with quote

Here are pictures of the knotter that I need knives for.
 
Back to top
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Minneapolis Moline All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters