Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Big 400 seat


 
Post new topic    
View previous topic :: View next topic  
Author Message
chuck machinist
Long Time User


Joined: 05 Jul 2011
Posts: 1178
Location: Chesapeake va

Report to Moderator

PostPosted: Fri Apr 19, 2013 5:28 pm    Post subject: Big 400 seat Reply to specific post Reply with quote

Had a wack at the seat today and of course the hinge pins became one with the seat. I was just about ready to grab my air grinder and cut the pins when I lifted the seat frame exposing two of the three base bolts. Off to the sand blaster then a good coat of primer,and f.-red. No silver paint to the rims yet though.The rubber torsion spring is shot ,but John Saeli supplied me with one to replace her.Pics to follow soon.
 
Back to top
View user's profile
Adirondack case guy
Tractor Guru


Joined: 04 Mar 2010
Posts: 6580


Report to Moderator

PostPosted: Sat Apr 20, 2013 4:33 am    Post subject: Re: Big 400 seat Reply to specific post Reply with quote

Chuck,
Did you get the hand throttle lever/shat installed and clocked? Enjoyed the chat yesterday.
Loren
 
Back to top
View user's profile
chuck machinist
Long Time User


Joined: 05 Jul 2011
Posts: 1178
Location: Chesapeake va

Report to Moderator

PostPosted: Sat Apr 20, 2013 5:41 am    Post subject: Re: Big 400 seat Reply to specific post Reply with quote

Morning Loren.I got the linkage all set,preloaded the spring on the throttle shaft and reached for my pistol drill to drill for the throttle handle.No drill .Sitting on the work bench at home.Shoot! We will get that tommorow.You sound well! Clean living and a good wiffy to keep you in tow.{healthy i mean}.Got to get some pics today! Thanks for the conversation.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters