Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

28in rims on a CA


 
Post new topic    
View previous topic :: View next topic  
Author Message
MMZAck
Regular


Joined: 05 May 2010
Posts: 376


Report to Moderator

PostPosted: Wed Jun 26, 2013 2:41 pm    Post subject: 28in rims on a CA Reply to specific post Reply with quote

I want to put 28in wheels on a CA for tractor pulling like on the CA in the picture. Any idea what wheel disc will fit? Massey 22? MM 335? I just want to know if that is a common 6 bolt disc with 6 loops for a common 28in rim and where to find them.

Thanks,

Zack

 
Back to top
View user's profile
David R Inman
Regular


Joined: 01 Aug 2012
Posts: 322


Report to Moderator

PostPosted: Thu Jun 27, 2013 2:34 am    Post subject: Re: 28in rims on a CA Reply to specific post Reply with quote

Besides checking to see if what ever rim you find has the correct clearence of the fenders, etc make sure to measure the distance on center of your CA and your prespective rim.

We ran into this a few weeks ago when we were trying to put wheels on a TO35 so we could run it some. We just glancrd, seen it had a 6 bolt hub like our WD45 s and thought we d be really smart and use two off a 45.... we didnt measure, and it dont work due to on center spacing being different. In our cass, no harm, we were just out a little time, as we hadnt gone out and bought somthing.
 
Back to top
View user's profile
dakota dave
Regular


Joined: 31 Jan 2005
Posts: 163


Report to Moderator

PostPosted: Fri Jun 28, 2013 4:36 pm    Post subject: Re: 28in rims on a CA Reply to specific post Reply with quote

A WD45 had 8 bolt wheels. be real hard to bolt to 6 bolt hubs. Those look like ford rims in the picture.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Allis Chalmers All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters