Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Ford 800 3 point won't go up


 
Post new topic    
View previous topic :: View next topic  
Author Message
Al07
New User


Joined: 21 Nov 2013
Posts: 4


Report to Moderator

PostPosted: Mon Nov 25, 2013 11:17 am    Post subject: Ford 800 3 point won't go up Reply to specific post Reply with quote

I recently had to pto shaft out and replaced the seal. I put oil back in and now the 3 point won"t move. Any ideas what might be wrong?
 
Back to top
View user's profile
souNdguy
Tractor Guru


Joined: 20 Aug 2002
Posts: 58432


Report to Moderator

PostPosted: Mon Nov 25, 2013 11:19 am    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

did you put oil back in both the rear end sump AND the hyd sump?

trans, rear, and hyds are 3 seperate sumps.. however pulling hte pto shaft out drains both the hyd and rear end sump.
 
Back to top
View user's profile
Al07
New User


Joined: 21 Nov 2013
Posts: 4


Report to Moderator

PostPosted: Mon Nov 25, 2013 11:21 am    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

Yes there is oil in both sumps. I replaced seal once before and didn't have this issue
 
Back to top
View user's profile
lonestarjeff
Tractor Expert


Joined: 25 Feb 2004
Posts: 2719
Location: The Colony, TX

Report to Moderator

PostPosted: Mon Nov 25, 2013 6:34 pm    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

Have you tried backing out the upper plug on the pump to clear out any bubbles? Do it while bumping the engine over w/ the starter(ignition off). I've lost pump pressure on my 860 when I did the pto seal.

Jeff
 
Back to top
View user's profile
souNdguy
Tractor Guru


Joined: 20 Aug 2002
Posts: 58432


Report to Moderator

PostPosted: Tue Nov 26, 2013 10:00 am    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

pluu plug on top side head of pump.. got oil there when cranking over?
 
Back to top
View user's profile
Al07
New User


Joined: 21 Nov 2013
Posts: 4


Report to Moderator

PostPosted: Fri Nov 29, 2013 8:32 am    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

Where exactly is that plug
 
Back to top
View user's profile
JMOR
Tractor Guru


Joined: 13 Aug 2007
Posts: 22556


Report to Moderator

PostPosted: Fri Nov 29, 2013 8:40 am    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

Al07 wrote:
(quoted from post at 12:32:51 11/29/13) Where exactly is that plug
where George has his bleeder hose attached, but you don't need the hose.

 
Back to top
View user's profile
souNdguy
Tractor Guru


Joined: 20 Aug 2002
Posts: 58432


Report to Moderator

PostPosted: Fri Nov 29, 2013 12:52 pm    Post subject: Re: Ford 800 3 point won't go up Reply to specific post Reply with quote

if a cylindrical pump, at the end.. there will be a plug onthe top side. may be inverted style plug and caked with dirt / hard to see.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Ford All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters