Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

John Deere One-way drill (pic)


 
Post new topic    
View previous topic :: View next topic  
Author Message
David from Kansas
Tractor Expert


Joined: 19 Nov 2000
Posts: 1799


Report to Moderator

PostPosted: Sat Jan 04, 2014 8:19 pm    Post subject: John Deere One-way drill (pic) Reply to specific post Reply with quote

Have never seen one of these but have heard about them. This one is located in southwest Kansas where they may have been more common.

 
Back to top
View user's profile
jdv
Regular


Joined: 08 Apr 2012
Posts: 297


Report to Moderator

PostPosted: Sat Jan 04, 2014 8:27 pm    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

I've always wanted one of those, where in Kansas is it located? As a kid I cut my teeth pulling a oneway, we ran the grain drill at the same time right behind it. It sure would save some time that away.
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 25533
Location: N Central Texas

Report to Moderator

PostPosted: Sun Jan 05, 2014 3:42 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

The model of plow was 1400(8" disk spacing) or 2400(10" disk spacing) but so far I haven't located the seeding attachment


 


Last edited by Tx Jim on Sun Jan 05, 2014 3:45 am; edited 2 times in total
Back to top
View user's profile
long green line man
Long Time User


Joined: 03 Feb 2008
Posts: 998


Report to Moderator

PostPosted: Sun Jan 05, 2014 7:36 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

I'm not sure, but I don't think a seeding att. was made for 1400 or 2400 disk tiller; Thinking pic is a 1900 seeding tiller ; PC-1466 .. It would be newer, made into early "70's...
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 25533
Location: N Central Texas

Report to Moderator

PostPosted: Sun Jan 05, 2014 8:10 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote


You're probably correct. Thanks for correcting my mistake.
 
Back to top
View user's profile
Case Nutty 1660
Tractor Guru


Joined: 08 Mar 2011
Posts: 13346


Report to Moderator

PostPosted: Sun Jan 05, 2014 8:28 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

Case made them as well this is mine, I got it out of Canada they sold very well in certain areas there this one is late sixtys build, they were made from the 40's -1970 or so by Case




 
Back to top
View user's profile
paul
Tractor Guru


Joined: 25 Dec 1997
Posts: 24436


Report to Moderator

PostPosted: Sun Jan 05, 2014 8:56 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

I assume that is just transport position to make them fit on the road, and they pivot out to a normal drill somehow for planting?

Paul
 
Back to top
View user's profile
JMS/.MN
Tractor Guru


Joined: 05 Mar 2009
Posts: 11980


Report to Moderator

PostPosted: Sun Jan 05, 2014 9:47 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

Nope- they run at an angle to till and seed at the same time.
 
Back to top
View user's profile
Case Nutty 1660
Tractor Guru


Joined: 08 Mar 2011
Posts: 13346


Report to Moderator

PostPosted: Sun Jan 05, 2014 9:58 am    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

they do run narrower for trans port but they do not run full width when in work mode, they run at a angle like a offset disc gang runs like in the pic above

 
Back to top
View user's profile
paul
Tractor Guru


Joined: 25 Dec 1997
Posts: 24436


Report to Moderator

PostPosted: Sun Jan 05, 2014 12:07 pm    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

Thanks guys.

Too far away from the wheat areas here to ever see anything like that.

Paul
 
Back to top
View user's profile
GaryinKs
Regular


Joined: 10 Apr 2011
Posts: 368


Report to Moderator

PostPosted: Sun Jan 05, 2014 2:17 pm    Post subject: Re: John Deere One-way drill (pic) Reply to specific post Reply with quote

This type outfit was popular in Canada, I have only seen 2 in NW KS, I would think that it would still be usable for dryland farming.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters