Yesterday's Tractor Co. Parts for Farm Tractors - Compare our Prices!
Click Here or call 800-853-2651 
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

MF-10 Baler question


 
Post new topic    
View previous topic :: View next topic  
Author Message
Robb Turner
New User


Joined: 18 Mar 2014
Posts: 2


Report to Moderator

PostPosted: Tue Mar 18, 2014 4:45 pm    Post subject: MF-10 Baler question Reply to specific post Reply with quote

I need to replace one of the disc's for the knotter timing on my MF-10 Baler. I'm not sure how to take the knotter drive shaft off to get to these. Does anyone know how to accomplish this?
 
Back to top
View user's profile
DeltaRed
Tractor Guru


Joined: 25 Feb 2010
Posts: 9968
Location: Delta,colorado

Report to Moderator

PostPosted: Wed Mar 19, 2014 6:37 am    Post subject: Re: MF-10 Baler question Reply to specific post Reply with quote

Robb,There is probably a little hidden pin holding them together.You may have to dissemble a bunch of parts to get to where you need to be.You NEED Book.You will NEED it to get everything readjusted when you put it back together.It may even tell how to take apart/repair.
 
Back to top
View user's profile
EJ70
Regular


Joined: 15 Apr 2012
Posts: 187


Report to Moderator

PostPosted: Thu Mar 20, 2014 10:02 am    Post subject: Re: MF-10 Baler question Reply to specific post Reply with quote

Try this site. As stated a book is very helpful for timing and adjusting. I have worked on MF12s many times.
Untitled URL Link

 
Back to top
View user's profile
Robb Turner
New User


Joined: 18 Mar 2014
Posts: 2


Report to Moderator

PostPosted: Tue Mar 25, 2014 5:21 am    Post subject: Re: MF-10 Baler question Reply to specific post Reply with quote

Thanks everyone. I ordered a repair manual. I have the operators manual but it wasn't much help. Hopefully the repair one will get me going by spring. Thanks again!
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Implement Alley All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
TRACTOR   PARTS TRACTOR   MANUALS
Same-Day Shipping! Most of our stocked parts ship the same day you order (M-F).  Expedited shipping available, just call!  Most prices for parts and manuals are below our competitors.  Compare our super low shipping rates!  We have the parts you need to repair your tractor.  We are a Company you can trust and have generous return policies!   Shop Online Today or call our friendly sales staff toll free (800) 853-2651.

YT Home  |  Forums Home

Copyright © 1997-2014 Yesterday's Tractor Co.

Powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters