Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

tubing bender


 
Post new topic    
View previous topic :: View next topic  
Author Message
88-1175
Regular


Joined: 10 Mar 2008
Posts: 409


Report to Moderator

PostPosted: Mon Oct 09, 2017 9:41 pm    Post subject: tubing bender Reply to specific post Reply with quote

wanting to get my son a tubing bender to bend 2 inch by .120 wall mild steel tube.any recommendations ??.looking for a bender for tube only,not a pipe bender with homemade dies.also the die would be a 180 degree die...
 
Back to top
View user's profile
ptfarmer
Tractor Guru


Joined: 01 Jul 2013
Posts: 5219
Location: San Antonio, Texas

Report to Moderator

PostPosted: Mon Oct 09, 2017 10:03 pm    Post subject: Re: tubing bender Reply to specific post Reply with quote

I have one of these https://www.jd2.com/p-32-model-3-bender.aspx it will bend up to 2" tubing (I use it for chassis in racecars).
 
Back to top
View user's profile
Cory Schmidt
Tractor Expert


Joined: 19 Dec 2011
Posts: 2345
Location: Two Rivers, wi

Report to Moderator

PostPosted: Wed Oct 11, 2017 3:17 pm    Post subject: Re: tubing bender Reply to specific post Reply with quote

RMD are made right down the road from where I work. Had one of the manual machines in the high school, worked good...where I work they use mostly Eaton Leonard, that's if you are looking for more heavier production machines
RMD benders

Eaton Leonard.

 
Back to top
View user's profile
Ray Tractor
Regular


Joined: 01 Dec 2014
Posts: 383


Report to Moderator

PostPosted: Fri Oct 13, 2017 12:22 pm    Post subject: Re: tubing bender Reply to specific post Reply with quote

I bought a JD2 bender for the ag shop. It seems to be well made. It cost about $400 plus about $300 for each set of dies. We used it to bend some chain link fence top rail and it worked good.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Tool Talk All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters