Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

530 gas starter question


 
Post new topic    
View previous topic :: View next topic  
Author Message
dacaseguy
Long Time User


Joined: 25 Apr 2008
Posts: 507
Location: Grants Pass, OR.

Report to Moderator

PostPosted: Thu Dec 07, 2017 7:51 pm    Post subject: 530 gas starter question Reply to specific post Reply with quote

I'm getting closer to firing up the new engine in my 530 I just rebuilt. This was one of them that you just keep thinking what's it need next.
The crank was bad, valves were shot, head had to be shaved, new pistons and sleeves, one rod was no good, starter bendix solenoid was bad,
needed new steering wheel, rockshaft seat was shot and more.
Tomorrow I will put gas in the tank and see what happens 🤔
I have a question on the starter safety switch. I got a new safety switch from John Salei and installed it. If I put the gearshift in the S position I
get nothing to the starter solenoid ? If I touch the two wire terminals together on the safety switch then I get juice to the solenoid and the engine
cranks? When I pulled the switch out I noticed a little plunger that must come up to engage the switch. Moving the gearshift lever I don't see the
plunger going down unless I push on it with a small screwdriver. Thanks Dick






 
Back to top
View user's profile
Graham of New Zealand
Regular


Joined: 19 Oct 2014
Posts: 156


Report to Moderator

PostPosted: Thu Dec 07, 2017 10:24 pm    Post subject: Re: 530 gas starter question Reply to specific post Reply with quote

Can you screw it down a bit further, adjustment fashion?
 
Back to top
View user's profile
dacaseguy
Long Time User


Joined: 25 Apr 2008
Posts: 507
Location: Grants Pass, OR.

Report to Moderator

PostPosted: Fri Dec 08, 2017 6:20 am    Post subject: Re: 530 gas starter question Reply to specific post Reply with quote

It has two shim washers under it. I thought I would try removing a shim. Dick
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Case and David Brown All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters