Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Calling rrlund


 
Post new topic    
View previous topic :: View next topic  
Author Message
StrongsOlivers
Regular


Joined: 12 Aug 2015
Posts: 254


Report to Moderator

PostPosted: Fri Dec 01, 2017 5:21 pm    Post subject: Calling rrlund Reply to specific post Reply with quote

Got a question for you. What does your bale bale spear look like on your 1365.
 
Back to top
View user's profile AIM Address
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 35106


Report to Moderator

PostPosted: Mon Dec 04, 2017 2:18 pm    Post subject: Re: Calling rrlund Reply to specific post Reply with quote

It's just home made,made to fit my Horst quick attach.
 
Back to top
View user's profile
StrongsOlivers
Regular


Joined: 12 Aug 2015
Posts: 254


Report to Moderator

PostPosted: Tue Dec 05, 2017 10:34 am    Post subject: Re: Calling rrlund Reply to specific post Reply with quote

Ok thanks. I'm just in planning stages for buildings bale spear and quick attach. Pulling pins is getting old.
 
Back to top
View user's profile AIM Address
rrlund
Tractor Guru


Joined: 21 Dec 2006
Posts: 35106


Report to Moderator

PostPosted: Tue Dec 05, 2017 1:35 pm    Post subject: Re: Calling rrlund Reply to specific post Reply with quote

I just took this picture of it from the house using the zoom. The second and third are of the quick attach I built for the 1600 using the one on the 1365 for a pattern so I can use all of my attachments and buckets on both loaders.



 
Back to top
View user's profile
StrongsOlivers
Regular


Joined: 12 Aug 2015
Posts: 254


Report to Moderator

PostPosted: Thu Dec 07, 2017 10:36 am    Post subject: Re: Calling rrlund Reply to specific post Reply with quote

Thanks for the pictures. Are those wedges with clips that hold the bottom two attaching points?
 
Back to top
View user's profile AIM Address
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> Oliver, Cletrac, Coop and Cockshutt All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters