Yesterday's Tractor Co.
Shop Now View Cart
   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   Ferguson John Deere Massey Ferguson Minn. Moline Oliver
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   Traditional YT Forum ViewClassic View   RegisterRegister 
 ProfileProfile    Log inLog in 

Lift Capacity 4010 versus 4020


 
Post new topic    
View previous topic :: View next topic  
Author Message
farmerjack
Regular


Joined: 18 Mar 2011
Posts: 57


Report to Moderator

PostPosted: Tue Jan 02, 2018 6:29 am    Post subject: Lift Capacity 4010 versus 4020 Reply to specific post Reply with quote

I see a 4020 and 4320 both have a 3 point lift capacity (24" rearward) of 3750 lbf. How does a 4010 compare to that?

thanks,
 
Back to top
View user's profile
Tx Jim
Tractor Guru


Joined: 14 Feb 1999
Posts: 25013


Report to Moderator

PostPosted: Tue Jan 02, 2018 7:14 am    Post subject: Re: Lift Capacity 4010 versus 4020 Reply to specific post Reply with quote


I think since 3 pt hitch & rockshaft are similar with same stand-by pressure but 4010 has smaller rockshaft piston seal(3.185 OD) while 4020 has piston seal(3.502 OD) therefore 4020 will lift more weight but how much I don 't know
 
Back to top
View user's profile
Brendon-KS
Tractor Expert


Joined: 18 Dec 2007
Posts: 2108
Location: Goessel, KS

Report to Moderator

PostPosted: Tue Jan 02, 2018 10:33 am    Post subject: Re: Lift Capacity 4010 versus 4020 Reply to specific post Reply with quote

Using your diameters the area of the 4010 piston would be 17% less than that of the 4020. If everything else in the system is equal (basically pressure and geometry) this same
reduction in piston area in theory should carry through to the lift force to give a value of 3100 lbs for the 4010. What we don't know is what the limiting factor is for the
3750 lbs rating the OP shows for the 4020. If it was limited by something other than pure lifting force, such as fore/aft stability, then the math won't tell us the whole story.
 
Back to top
View user's profile
Display posts from previous:   
Post new topic    Yesterday's Tractors Forum Index -> John Deere All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  

TRACTOR PARTS TRACTOR MANUALS
Fast Shipping!  Most of our stocked parts ship within 24 hours (M-Th). Expedited shipping available, just call! Most prices for parts and manuals are below our competitors. Compare our super low shipping rates! We have the parts you need to repair your tractor. We are a company you can trust and have generous return policies. Shop Online Today or call our friendly sales staff toll free (800) 853-2651. [ About Us ]

YT Home  |  Forums

Modern View Forum powered by phpBB © 2001, 2005 phpBB Group

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters