View previous topic :: View next topic |
Author |
Message |
aprice0101 New User
Joined: 05 Jan 2018 Posts: 6
Report to Moderator
|
Posted: Fri Jan 05, 2018 2:28 pm Post subject: 58' TO-35 Injection pump help |
|
|
Took off the injection pump on my 23c standard diesel to fix fuel leaks. I understand that i need to match the scribe line of the letter "G" up with the cir-clips scribe line with #1 at 19 deg BTC, howeverr, when i get the engine spun there, and insert the 1/4 in rod into the flywheel through the check hole, the pump lines up slightly above "H". The pump, pump shaft and drive gear are all keyed as it can only go in 1 way.....is there something i am missing or something i can do? tractor ran before taking it off by the way. Someone please chime in, i'm relitively frustrated with it right now. Thank you. |
|
Back to top |
|
 |
Dieseltech Tractor Guru
Joined: 29 Feb 2012 Posts: 5638 Location: Indiana
Report to Moderator
|
Posted: Fri Jan 05, 2018 3:03 pm Post subject: Re: 58' TO-35 Injection pump help |
|
|
Put it back on using the flange scribe line. That snap ring may not have been set right in the first place.. |
|
Back to top |
|
 |
aprice0101 New User
Joined: 05 Jan 2018 Posts: 6
Report to Moderator
|
Posted: Fri Jan 05, 2018 3:11 pm Post subject: Re: 58' TO-35 Injection pump help |
|
|
I'll give it a try in the morning and report back, where exactly will the flange scribe line line up with? |
|
Back to top |
|
 |
aprice0101 New User
Joined: 05 Jan 2018 Posts: 6
Report to Moderator
|
Posted: Fri Jan 05, 2018 3:25 pm Post subject: Re: 58' TO-35 Injection pump help |
|
|
Never mind! I found an extremely faint scribe line of the drive gear side flange, also looking at pictures before hand, it seems to copy what you suggested to do, thank you....its about 1/8 in off that scribe line right now. |
|
Back to top |
|
 |
aprice0101 New User
Joined: 05 Jan 2018 Posts: 6
Report to Moderator
|
Posted: Fri Jan 05, 2018 3:38 pm Post subject: Re: 58' TO-35 Injection pump help |
|
|
So, just to be sure, since it's a keyed shaft and gear, that portion should be good and within the ""twist" adjustment range which should be close to that scribe line? |
|
Back to top |
|
 |
aprice0101 New User
Joined: 05 Jan 2018 Posts: 6
Report to Moderator
|
Posted: Tue Jan 09, 2018 7:44 am Post subject: Re: 58' TO-35 Injection pump help |
|
|
CVPost-Dieseltech wrote: | (quoted from post at 16:03:15 01/05/1 Put it back on using the flange scribe line. That snap ring may not have been set right in the first place.. |
Okay here's an update, put it to the scribe line and it sputtered a bit then blew a bit out the air intake, I haven't touched valves, or front set timing only the cav pump. Tractor was running very good a few days ago before I pulled the cav pump. |
|
Back to top |
|
 |
aprice0101 New User
Joined: 05 Jan 2018 Posts: 6
Report to Moderator
|
Posted: Tue Jan 09, 2018 9:25 am Post subject: Re: 58' TO-35 Injection pump help |
|
|
Another update.... Spill tested it, g indeed lines up with the circlip scribe on #1.... |
|
Back to top |
|
 |
|